TFA9890A Audio IC | NXP Boosted Class-D Amplifier

₨ 350

NXP Boosted Class-D Speaker Amplifier IC

The TFA9890A is an NXP mono class-D audio amplifier IC with an internal boost stage and an adaptive sound maximizer. It drives a speaker in a bridge-tied load configuration and has distinct boost, mute and disabled operating states, which lets you isolate a speaker-path fault step by step. It comes in a 49-bump wafer-level package measuring 3.37 × 2.97 mm, so it suits board-level replacement where the speaker output has failed. This listing covers the single IC. Confirm the variant suffix against the original marking before ordering, because NXP ships several TFA9890 variants.

16 People watching this product now!
Description

TFA9890A Audio IC for Board-Level Speaker Repair

The TFA9890A audio amplifier IC from NXP is a high-efficiency mono class-D device with a built-in boost converter. Its name refers to the 9.5 V boosted audio system, meaning the IC raises its internal supply when the battery voltage runs low and the speaker needs more headroom. For a technician, this explains why speaker output can change with battery level. This listing covers the standalone IC, supplied for replacement on the speaker output path of a board.

Key Technical Highlights

The device is a mono bridge-tied load (BTL) class-D amplifier. It pairs an adaptive sound maximizer with speaker protection, so it pushes more output while guarding the speaker against overload. The datasheet defines three operating states. Boost mode applies when the battery voltage is boosted. Mute mode keeps the output switching while the audio input is muted. Disabled mode applies when the class-D stage runs from an external supply instead of the internal boost. Knowing these states helps you tell a software-controlled mute from a real hardware fault on the output stage.

The IC uses a 49-bump WLCSP (wafer-level chip-size package) measuring 3.37 × 2.97 mm. Bump count and footprint matter at the bench. You need a reflow setup and a stencil or reballing method that matches this footprint before you attempt a replacement.

Where It Fits in the Speaker Repair Workflow

In a no-sound or weak-speaker complaint, check the speaker connector, the audio routing from the processor, and the supply rails before you suspect this IC. Once the supply is confirmed, the boosted rail and the output pins become the next checkpoints. A dead or shorted output stage, a damaged speaker path, or a fault that appears after a liquid damage repair on the audio section all point toward this amplifier.

Use a hot-air station with a controlled profile and quality flux for removal and placement. After replacement, verify the speaker output with a test tone and check the output under low-battery conditions before final reassembly. Retest in each operating state if the device still shows intermittent behavior.

Sourcing and Variant Checks

NXP lists several TFA9890 variants that differ by suffix and package status, and distributor records show different output power figures for each. Read the marking on the original component and match its suffix before you order. This listing does not state a supply voltage range or output wattage for this part, because those values change between variants. Check the NXP datasheet for the exact variant you plan to install. That step prevents mismatched replacements and keeps your repair records accurate.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Mono class-D BTL speaker amplifier
  • Boosted 9.5 V internal supply system
  • Adaptive sound maximizer with speaker protection
  • Distinct boost, mute and disabled operating modes
  • 49-bump WLCSP package, 3.37 × 2.97 mm
  • Surface-mount board-level replacement

Specifications

BrandNXP
ModelTFA9890AUK
CategoryAudio Amplifier IC
CompatibilityIC-level part for mono speaker output circuits
Supported DevicesNot device-specific; verify against the original board marking
TechnologyBoosted class-D amplifier with adaptive sound maximizer and speaker protection
ChannelsMono (BTL)
PackageWLCSP49 (49 bumps)
Dimensions3.37 × 2.97 mm

Common Repair Uses

  • Typical board-level scenarios where this IC gets replaced or checked.
  • Replacing a dead or shorted speaker amplifier IC on a no-sound board
  • Diagnosing weak or distorted speaker output before replacing the speaker
  • Checking the boosted supply rail when speaker volume drops on low battery
  • Reflowing or reballing the 49-bump WLCSP after a board-level fault
  • Restoring the speaker path after liquid damage on the audio section
  • Confirming mute and disabled states during audio troubleshooting

Compatible Devices

  • IC-level component; fitment is scoped to mono speaker output circuits using this footprint, not to a specific phone model.
  • Mono BTL speaker output stages
  • Boards using the TFA9890AUK 49-bump WLCSP footprint
  • Boosted-supply audio designs (9.5 V boosted system)

FAQ

What is the product name?
The product name is TFA9890A Audio IC.
What is the brand of this product?
The brand of this product is NXP.
What is the model of this product?
The model of this product is TFA9890AUK.
What is this product used for?
This product is used as a mono class-D speaker amplifier IC for board-level speaker repair and replacement.
Which devices are compatible with this product?
This product is compatible with mono speaker output circuits using the TFA9890AUK 49-bump WLCSP footprint. Device-specific fitment should be verified against the original board marking.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What does the 9.5 V in the name mean?
The 9.5 V refers to the internal boosted audio system. The IC raises its internal supply to support speaker output when the battery voltage is low.
What package is this IC supplied in?
This IC is supplied in a WLCSP49 wafer-level chip-size package with 49 bumps, measuring 3.37 × 2.97 mm.