RELIFE RL-1520 1.5mm Desoldering Wick

₨ 850

RELIFE RL-1520 Desoldering Wick for Fine Pads

The RELIFE RL-1520 is a 1.5mm desoldering wick made from 100% copper braid for precise solder removal on compact boards. Its no-clean, halide-free residue means you can often skip cleaning after each joint. The sealed thumb-wheel dispenser keeps the 2.0 metre spool protected from moisture and lets you feed braid with one hand. Technicians use it for SMD pads, fine connector pins, and narrow IC legs where wider wicks risk bridging. It suits phone repair benches, laptop motherboard work, and any shop that needs a reliable narrow braid for daily rework.

Out of stock

13 People watching this product now!
Description

RELIFE RL-1520 Desoldering Wick for Precision Board Repair

The RELIFE RL-1520 desoldering wick is a 1.5mm copper braid built for technicians who work on dense boards where a wider wick would bridge neighboring pins. Your repair bench gets a consistent braid width for removing excess solder from SMD pads, fine connector pins, and tight IC legs. The braid is made from 100% copper, and its fine weave draws molten solder into the strands through capillary action. Because the residue is halide-free and non-conductive, you do not need to clean the board after every removal. The 2.0 metre length gives you enough wick for a full day of rework without constant reloading. Many technicians keep a 1.5mm braid at the bench for jobs where wider wicks cause collateral damage.

Where the 1.5mm Width Fits in Your Workflow

Board-level repair usually follows a clear sequence: diagnosis, component removal, pad preparation, and then replacement. Desoldering sits in the middle of that sequence, and the wick you choose determines how much collateral damage you cause. A 1.5mm braid suits narrow SMD pads and fine connector pins, where a 2.5mm or 3.0mm wick would cover adjacent pads and pull solder from joints you never meant to touch. Wider braids absorb more solder per pass, but they also spread contact across neighboring pins. The RL-1520 gives you control when the job calls for precision. Place the braid over the joint, then press the heated iron tip onto the wick rather than onto the board. Watch the solder move into the copper, and lift the wick once it stops absorbing. Cut off the saturated section before the next pass so the used part does not return solder to the pad. This habit keeps pads clean and reduces the risk of lifted traces during a long session.

Residue, Flux, and Board Cleaning

The RL-1520 uses a no-clean design, and its residue is halide-free and non-conductive. On many boards you can skip the aggressive cleaning step, which saves time during a busy shift. You should still inspect the pads under a magnifier or microscope before you reflow a new component, because leftover flux can affect how a fresh joint wets. The braid’s fine weave pulls solder effectively, but a thin film may remain on the pad, and a quick visual check catches it early. Store the spool in its sealed thumb-wheel dispenser between sessions. The sealed housing protects the copper from moisture, which helps preserve absorption and extends the working life of the spool. Keep the dispenser away from humid corners of the shop and close it after each use so the braid stays ready for the next job.

Dispenser Handling and Daily Use

The thumb-wheel dispenser lets you feed the braid with one hand while the other hand holds the iron. You control how much wick comes out, so you never pull loose lengths across the bench. Feed only what the current joint needs, then cut the used section cleanly before moving on. A single 2.0 metre spool covers a long run of jobs, which suits repair shops that handle many devices each day. Pair the RL-1520 with a stable soldering station and a clean tip for the best results. Set the iron temperature on a spare board before you touch the working device. Small adjustments at the start protect your pads, and that habit pays off across hundreds of repairs.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 100% copper braid for strong solder absorption
  • 1.5mm width suited to narrow SMD pads and fine pins
  • 2.0 metre length for extended bench use
  • Halide-free, non-conductive, no-clean residue
  • Fine braid weave for strong capillary action
  • Thumb-wheel dispenser for one-handed feeding
  • Sealed dispenser protects the wire from moisture
  • Part of the RELIFE 1.5mm to 3.5mm desoldering wick range

Specifications

BrandRELIFE
ModelRL-1520
CategoryDesoldering Wick
CompatibilityUniversal, not device-specific
TechnologyNo-clean, halide-free residue
Material100% copper
Dimensions1.5 mm width, 2.0 m length

Common Repair Uses

  • Verified board-level desoldering workflows
  • Removing bridged solder between fine-pitch IC pins
  • Clearing excess solder from SMD resistor and capacitor pads before replacement
  • Freeing connector pins during charging port or flex replacement
  • Preparing pads before reflowing a fresh component
  • Removing a component from a narrow pad array
  • Clearing solder shorts on a dead phone motherboard
  • Preparing a board surface before BGA reballing
  • Cleaning excess solder from laptop motherboard connectors

Compatible Devices

  • Universal board-level scope, not device-specific
  • Universal PCB solder pads on compact boards
  • SMD component pads on compact boards
  • Fine-pitch connector pins
  • Narrow IC leg solder bridges
  • Small-gauge component leads
  • Smartphone motherboard pads (chipset-agnostic)
  • Laptop and PC motherboard solder joints
  • Fine-pitch flex and connector pads

FAQ

What is the product name?
The product name is RELIFE RL-1520 Desoldering Wick.
What is the brand of this product?
The brand of this product is RELIFE.
What is the model of this product?
The model of this product is RL-1520.
What is this product used for?
This product is used for removing excess solder from PCB pads, SMD components, and connector pins during repair work.
Which devices are compatible with this product?
This product is compatible with universal board-level desoldering work and is not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this wick need cleaning after use?
The RL-1520 leaves halide-free, non-conductive residue, so many boards do not require cleaning, though pads should still be inspected before reflow.
Which pad sizes suit the 1.5mm width?
The 1.5mm width suits narrow SMD pads and fine connector pins, while wider pads and larger joints are better served by a 2.5mm or wider braid.