Mechanic V5B45 Low Temp Solder Paste 138°C 42g

₨ 1

V5B45 Low Temperature Solder Paste for BGA and SMD Work

The Mechanic V5B45 low temperature solder paste melts at 138°C, so you can reflow BGA and SMD joints without pushing heat into nearby ICs and plastic parts. The alloy is Sn42Bi58, a tin and bismuth mix that reflows at a much lower point than standard solder paste. Each 42g pack gives your repair bench enough material for several reballing and component jobs. Use it for controlled reflow on motherboards, laptop boards, and other heat-sensitive circuit boards, and pair it with a stencil or a fine application tool for clean, even deposits.

Out of stock

17 People watching this product now!
Description

V5B45 Low Temperature Solder Paste for Controlled BGA Reflow

A V5B45 low temperature solder paste gives you control over the heat that reaches a board. This paste melts at 138°C, which sits far below the 220°C range where standard solder pastes flow. For a technician working on phones, laptops, and tablets, that gap matters. Heat-sensitive ICs, plastic connectors, and flexible sections tolerate less thermal stress than the main board, so a lower melting point reduces the risk of damage during reflow. The V5B45 fits workflows built around BGA reballing, component replacement, and pad repair on compact, densely packed boards.

Alloy Composition and Melting Behavior

The V5B45 uses an Sn42Bi58 alloy, with about 42 percent tin and 58 percent bismuth. That ratio sets the melting point at 138°C. Bismuth-rich alloys flow at lower temperatures, so you complete reflow before heat spreads across the entire board. Once the joint cools, it forms a stable mechanical and electrical bond. Keep one trade-off in mind. Sn42Bi58 joints are more brittle than tin-rich joints under sustained bending or impact, so avoid placing a repaired board where flex or frequent knocks will stress the solder. The paste has a smooth, bubble-free consistency that helps you deposit clean, even volumes on each pad, which reduces bridging and cold joints on fine-pitch work.

Application Workflow on BGA and SMD Parts

Start every job with clean pads. Remove old solder with a wick, then clean the flux residue so the new paste bonds to bare copper. Apply the V5B45 through a stencil for BGA reballing, or with a fine tool for SMD pads, and keep the deposit even across each pad row. Place the component carefully and reflow with your hot air station, moving the nozzle in steady passes so heat reaches every joint evenly. Watch the paste as it melts. Once the joints look bright and settle into place, stop applying heat and let the board cool naturally. Avoid forcing the cooldown with strong air, since rapid temperature shifts can crack fresh joints. Keep airflow gentle so nearby small components do not shift before the alloy sets. After the board cools, check continuity with a multimeter, and inspect the joints under a microscope if your bench has one.

Storage, Handling and Safety

Store the container tightly closed in a cool place, and keep it away from food, drink, and animal feed. The product information warns that inhalation and ingestion are harmful, and that repeated skin contact causes problems, so work in a ventilated area and wash your hands after each session. Avoid eating, drinking, or smoking while you handle the paste. Transfer a small amount to your work tray rather than opening the full pack for every job, which limits exposure and keeps the rest of the paste clean. If paste is swallowed, seek medical attention immediately. These habits protect you on a busy repair bench, where paste tends to end up on tools, gloves, and nearby boards.

Additional information
Weight0.4 kg
Q & A
Please login to post questions

Key Features

  • 138°C melting point
  • Sn42Bi58 alloy
  • 42g package
  • Smooth, bubble-free consistency
  • Strong tin bonding with good conductivity
  • Large solder load for clean pad coverage
  • Suited to BGA and SMD work
  • Suited to stencil and manual application

Specifications

BrandMechanic
ModelV5B45
CategorySolder Paste
CompatibilityUniversal, not device-specific
TechnologyLow temperature solder paste, 138°C melting point
MaterialSn42Bi58 solder alloy with flux
Weight42g

Common Repair Uses

  • BGA IC reballing with a stencil
  • Replacing SMD components on phone boards
  • Reflowing heat-sensitive ICs at a lower temperature
  • Pad repair and tin re-application on motherboards
  • Laptop board component replacement
  • Re-attaching BGA chips after board repair

Compatible Devices

  • Mobile phone motherboards for BGA and SMD reflow
  • Laptop motherboards and related circuit boards
  • Tablet and other compact SMD/BGA boards

FAQ

What is the product name?
The product name is Mechanic V5B45 Low Temperature Solder Paste 138°C 42g.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is V5B45.
What is this product used for?
This product is used for SMD and BGA soldering on heat-sensitive circuit boards.
Which devices are compatible with this product?
This product is universal and not device-specific. It is used on phone, laptop, and tablet circuit boards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the melting point of V5B45 solder paste?
The V5B45 melts at 138°C.
Is V5B45 suitable for BGA reballing?
Yes. The V5B45 is designed for soldering SMD and BGA components, which includes reballing work.