KADA Soldering Iron Handle 5 Hole 24V 50W Rework Station
₨ 1,200
KADA Soldering Iron Handle 5 Hole for Rework Stations
This KADA soldering iron handle replaces a worn or damaged grip on KADA 858, 858D, 85D+, 8858, 878A and 878 soldering stations. It uses a 5-pin, 5-hole female connector on a DC 24V, 50W circuit, so it plugs straight into the station without rewiring. The metal body carries a heat-resistant silicone sleeve that keeps your hand clear of the barrel during long joint-work sessions. An ESD-safe build supports careful work on sensitive phone board ICs, and the kit includes a 900M-T-I tip. Restore your bench without buying a full station.
In stock
KADA Soldering Iron Handle 5 Hole: Connector, Power and Workflow Fit
A KADA soldering iron handle controls how power and heat travel from your rework station to the working tip, so the handle matters more than most bench parts. This 5-hole model fits the KADA 858, 858D, 85D+, 8858, 878A and 878 family, which uses a 5-pin female connector on a DC 24V, 50W circuit. You get a direct replacement that keeps your station’s existing behavior intact, rather than an upgrade that changes how the tip responds. When your old handle cracks, loses its grip or shows a damaged cable, this replacement restores full use of the station without the cost of a new unit. Before you order, count the holes on your current socket and read the voltage label on your station, because those two checks decide whether this handle fits your bench. The sections below cover the connector match, the grip and build, and how the handle fits into a daily repair workflow.
Connector and Electrical Match
The handle uses a five-pin connector with a matching five-hole female layout, which lines up with the socket on the KADA stations listed above. It operates on DC 24V at 50W, so the station supplies the power and the handle never connects to mains directly. Compare the pin count on your old handle with the new one before you fit it, and check that the cable routes cleanly from the iron to the station without strain. The listed cable length is 68 cm, which gives enough reach for most benches while keeping the lead clear of your work area. Mismatched voltage or a loose pin is the fastest route to a dead heater or a station that refuses to heat, so verify the connector at every swap. Inspect the pins for bent or corroded contacts first, because one bent pin stops the handle from seating fully. Seat the connector firmly, power the station on at a low setting and confirm the heater responds before you start a real job.
Grip, Heat Protection and Build
The metal body carries a high-temperature silicone sleeve that protects your fingers when the barrel runs near the upper end of the 120 to 480°C range. The sleeve gives a firm, non-slip grip, which helps your hand stay steady during fine joint work on tight phone boards. At about 90 g, the handle sits light in your hand and reduces wrist fatigue on long repair sessions. The ESD-safe construction supports careful handling of sensitive ICs such as CPUs and MOSFETs, where static discharge can cause hidden damage. Keep the iron in its stand between joints, and never strike the tip against the bench to knock off solder. Good grip control at the handle translates directly into cleaner pad work and fewer lifted traces.
Tip, Workflow and Daily Use
The kit includes a 900M-T-I tip, which suits standard board-level soldering with this handle family. Use the tip for through-hole jumpers, pin reflow on connectors and tinning pads before component placement. Start each session by tinning the tip, then adjust the station to a temperature that wets the joint without burning off the flux. Clean the tip on a damp sponge or brass wool between joints, because oxidized tips transfer heat poorly and slow down your work. Many technicians keep a spare handle on the bench for fast swaps during a busy repair day, which cuts downtime when one station needs service. Combine this handle with a fine-tip cleaner, a stable stand and a magnifier, and your bench stays productive without rework.
| Weight | 0.9 kg |
|---|
Key Features
- ✓5-pin, 5-hole female connector for KADA stations
- ✓DC 24V, 50W operating rating
- ✓High-temperature silicone sleeve over the grip
- ✓ESD-safe construction for sensitive ICs
- ✓Temperature range of 120 to 480°C
- ✓Includes a 900M-T-I soldering tip
- ✓Cable length of 68 cm
- ✓Weight of about 90 g
Specifications
| Brand | KADA |
|---|---|
| Category | Soldering Iron Handle |
| Compatibility | KADA 858, 858D, 85D+, 8858, 878A and 878 soldering stations |
| Supported Devices | Stations with a 5-pin, 5-hole DC 24V female socket |
| Technology | ESD-safe, high-temperature silicone grip, 120 to 480°C range |
| Material | Metal body with silicone sleeve |
| Input Voltage | DC 24V |
| Power Rating | 50W |
Common Repair Uses
- ✓Replacing a damaged handle or grip on KADA stations, plus everyday board-level soldering
- ✓Replacing a cracked or worn handle on a KADA 858-series station
- ✓Restoring a station with a damaged iron cord or loose socket
- ✓Swapping the handle during a repair day to keep the bench running
- ✓Through-hole jumper work on phone boards (jumper lagana)
- ✓Pin reflow on connectors and flex cable pads
- ✓Tinning and cleaning pads before component placement
- ✓Board-level soldering on small-scale PCB repair benches
Compatible Devices
- ✓KADA 858-series and 878-series rework stations with a 5-pin, 5-hole female connector
- ✓KADA 858 soldering station
- ✓KADA 858D soldering station
- ✓KADA 85D+ soldering station
- ✓KADA 8858 soldering station
- ✓KADA 878A soldering station
- ✓KADA 878 and 878D soldering stations
- ✓Any station with a matching 5-pin, 5-hole DC 24V female socket
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What connector and voltage does this handle need?
Does this handle include a soldering tip?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



