Relife RL-068 Mini Polishing Drill with 8 Grinding Heads
₨ 3,800
Mini Polishing Drill for Mobile Repair with 8 Heads
The Relife RL-068 gives your repair bench a compact rotary tool with three speed levels and a motor rated at 12,000 r/min. It ships with eight grinding heads, so you can move from IC edge grinding to bracket cutting and screw head removal without switching tools. The lithium battery recharges over a Type-C port at DC 5 V, which keeps cables off your bench during board work. At roughly 53 grams, it stays steady in one hand for long grinding sessions. Use it for residue removal, board-level cleaning, and mobile phone IC work.
In stock
RL-068 Mini Polishing Drill for Mobile Repair Work
A mini polishing drill for mobile repair earns its spot on the bench when fine work needs more control than a hand file and less bulk than a full rotary station. The Relife RL-068 fills that role. You get a handheld rotary tool with three speed settings, eight grinding heads, and a rechargeable battery, so no cable pulls at your hands while you work on a motherboard. Most of your bench time goes to small corrections: lifting a shield, cleaning a pad, trimming a bracket edge, or removing residue before a new part goes on. This drill covers those jobs in one tool. It sits between diagnostics and the soldering or rework stage, where clean, flat surfaces decide whether a part seats properly and stays put. Your repair bench gains the most from a tool that stays out of the way.
Motor, Speed Control, and Battery Details
Speed selection decides how clean your cut stays on a board, so start at the lowest setting and climb only when the material demands it. The RL-068 offers three speed levels, which lets you slow down for thin brackets and push harder when you need to remove material quickly. The motor is rated at 12,000 r/min with about 3 W of output, enough for light grinding on a small area without rushing the tip. Power comes from a 13450 lithium cell rated at 3.7 V and 650 mAh, which works out to roughly 2.4 Wh. You recharge it through a Type-C port at DC 5 V and about 0.5 A, so any standard low-current USB adapter on your bench will do. At 155 mm long and about 53 grams, the body sits comfortably in one hand and keeps your wrist steady during fine passes. Charge between jobs rather than mid-cut, so the battery stays ready for the work that matters.
Eight Grinding Heads for Different Board Tasks
The set includes eight grinding heads, and each one targets a different part of the job. A fine tip suits IC cover edges and tight corners, while a larger head works better for clearing pad residue or shaving a bracket. The tool uses a plug-in clip, so you change heads in seconds when you move from one board to the next. Sort the heads by size in a tray beside your bench so you never hunt for the right tip mid-repair. Start each job with the head that removes the least material, and step up only when the surface demands it. That habit protects the surrounding solder mask and keeps your cut precise. Replace a bent or chipped head early, because a damaged tip scratches the board surface and widens a cut you meant to keep narrow.
Practical Board-Level Repair Workflows
Board-level repair puts this drill to work in predictable ways. Grinding away old glue and residue leaves a flat surface before you reflow a new component. Cutting through a shield or bracket gives you access to the part underneath without lifting the entire assembly. Removing screw heads that strip under pressure is another job where a small tip gives you control that a larger tool cannot match. Polishing light corrosion on contacts and housing parts keeps your work clean and your joints reliable. A practical sequence helps: mark the area, set the lowest speed that moves material, work in short passes, and check the surface under your microscope before you move on.
| Weight | 0.10 kg |
|---|
Key Features
- ✓Three speed levels for controlled grinding
- ✓Eight grinding heads for different board tasks
- ✓Motor rated at 12,000 r/min
- ✓Rechargeable 3.7 V 650 mAh battery
- ✓Type-C charging at DC 5 V
- ✓Plug-in clip for quick head changes
- ✓Lightweight body, about 52.8 g
- ✓Compact 155 mm length for one-hand control
Specifications
| Brand | Relife |
|---|---|
| Model | RL-068 |
| Category | Polishing and Grinding Tools |
| Compatibility | Universal, not device-specific |
| Technology | Rechargeable lithium battery, 3-speed variable control |
| Input Voltage | DC 5 V ±0.3 V |
| Power Rating | 3 W |
| Dimensions | 155 × 16 × 17.8 mm |
Common Repair Uses
- ✓Removing old glue and residue before reflowing a component
- ✓Cutting shield cans and brackets to reach components underneath
- ✓Grinding IC cover edges during chip-level work
- ✓Removing stripped screw heads on phone assemblies
- ✓Cleaning pads and contacts before soldering
- ✓Polishing light corrosion on contacts and housing parts
- ✓Trimming bracket edges during board reassembly
- ✓Shaping small metal parts during fitting
Compatible Devices
- ✓Universal scope, not device-specific
- ✓Mobile phone motherboards at board level (scope set by head and technique)
- ✓Mobile phone IC packages and cover edges
- ✓Shield cans and metal brackets
- ✓Screw heads on phone and laptop assemblies
- ✓Solder pads and contact areas during cleaning
- ✓Housing components and light metal parts
- ✓Glue and residue removal on PCBs
- ✓Light corrosion on contacts and housings
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What charger does the RL-068 use?
What motor speed does the RL-068 reach?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



