Mechanic CS01 Screen Separation Cutting Wire 0.06mm 100M

₨ 300

H2: Mechanic CS01 Screen Separation Cutting Wire 0.06mm

The Mechanic CS01 gives your repair bench a fine cutting line for separating LCD and OLED phone screens from their frames. This 0.06mm wire comes on a 100 meter spool, so one purchase covers many front panel jobs. The carbon steel alloy line runs into the adhesive gap under bonded glass, letting you cut the bond before you lift the panel. Use it whenever the glass is glued tight and a pry tool alone risks cracking the display. It is a practical consumable for daily front glass and display replacement work.

In stock

12 People watching this product now!
Description

H2: LCD and OLED Screen Separation Cutting Wire for Phone Repair

Screen separation cutting wire sits at the start of most front panel replacements. When the glass is bonded to the frame, you need a line that can slide into the adhesive layer and cut it cleanly. The Mechanic CS01 at 0.06mm gives you that fine line, supplied as a 100 meter spool that keeps your bench stocked across many jobs. It is built for LCD and OLED assemblies where the front panel is glued to the chassis. Your workflow begins here, before any board, flex, or connector work starts.

H3: Where the Wire Fits in Your Screen Repair Workflow

Screen separation comes early in the front panel sequence. You soften the adhesive edge with gentle heat, then guide the wire between the glass and the frame to cut through the bond. Once the glass lifts clear, you move on to removing old adhesive and fitting the new panel. The CS01 handles only this stage, so it works alongside your heat source, suction cup, and pry tools rather than replacing them. Steady hands matter more than force here, because excess tension can crack the glass or damage the display edge.

H3: Working With the 100 Meter Spool

A 100 meter length gives you enough wire for repeated cuts without reloading often. Unwind only a working section and keep the line taut while you pull it through the gap. Avoid sharp kinks, since a kinked strand can weaken at the bend and snap during a cut. Trim off the length you need for the current device so the remaining spool stays clean and easy to handle. Store the spool in a dry drawer between sessions to keep dust and moisture off the line.

H3: Choosing the Right Diameter for Your Bench

This variant measures 0.06mm in diameter. Finer wires slide into tighter adhesive gaps, while slightly heavier wires offer more strength when the bond is thick. Match the diameter to the devices you handle most often. If your workload includes many slim-bezel phones, keep a second spool of a different diameter ready for variety. Test the cut on a practice panel before you start a customer job, so you learn how much tension your hands apply. That small check saves glass and time on the real repair.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 100 meter spool length for repeated screen separation jobs
  • 0.06mm wire diameter for fine adhesive gaps
  • Carbon steel alloy construction
  • Designed for LCD and OLED phone screen separation
  • One spool per purchase

Specifications

BrandMechanic
ModelCS01
CategoryScreen Separation Cutting Wire
CompatibilityUniversal, not device-specific
Supported DevicesLCD and OLED phone screen assemblies
MaterialCarbon steel alloy
Diameter0.06mm
Length100m

Common Repair Uses

  • Front glass replacement on LCD phones
  • Front glass replacement on OLED phones
  • Separating a cracked front panel from its frame
  • Removing a display assembly after cracked glass damage
  • Preparing a screen assembly for adhesive cleaning and refitting

Compatible Devices

  • Universal, not device-specific. Scope is LCD and OLED phone screen assemblies with adhesive-bonded front panels.
  • LCD phone screen assemblies with front glass bonded to the frame
  • OLED phone screen assemblies with front glass bonded to the frame
  • Front glass panels glued to a device chassis
  • Display modules that require adhesive separation before removal
  • Universal, not device-specific: no model list has been verified for this product

FAQ

What is the product name?
The product name is Mechanic CS01 Screen Separation Cutting Wire 0.06mm 100M.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is CS01.
What is this product used for?
This product is used for separating LCD and OLED phone screens from their frames during front panel replacement.
Which devices are compatible with this product?
This product is compatible with LCD and OLED phone screen assemblies with adhesive-bonded front panels. It is universal and not tied to a specific device model.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is this wire suitable for LCD and OLED screens?
Yes. The wire is designed for separating LCD and OLED phone screens bonded to the frame.
What diameter is this cutting wire?
This variant has a 0.06mm diameter and comes on a 100 meter spool.