MECHANIC V70 Magnetic Heat Resistant Repair Mat 20×14 Inch

₨ 2,500

Magnetic Repair Mat for Mobile Repair Benches

The MECHANIC V70 is a 51.5 x 36.5 cm magnetic repair mat for technicians who work on phones, drones, and small electronics. Its magnetic zone holds screws in place during disassembly, and the antistatic surface supports safer board handling. The mat carries a heat resistance rating of about 120 to 150°C and measures roughly 4 mm thick. At 0.89 kg, it stays stable on the bench yet moves easily between workstations. You can use one surface to manage each stage of a repair, from opening the device to final reassembly.

In stock

19 People watching this product now!
Description

How the MECHANIC V70 Fits Your Mobile Repair Workflow

The MECHANIC V70 is a magnetic repair mat for mobile repair, built for a crowded bench. Its working area measures 51.5 x 36.5 cm, which gives you room to lay out a phone, its screws, and your tools at the same time. A dedicated magnetic zone holds fasteners and small steel parts in place while you work through each stage of the repair. The surface is antistatic, so it suits handling of exposed boards, ICs, and other sensitive electronics. Heat resistance is rated at about 120 to 150°C, which defines where the mat fits in your soldering and rework tasks. Technicians who service phones, drones, and general electronics will find this layout practical for daily bench work.

Magnetic Zone for Screws and Small Parts

Phone screws are small, and one that rolls off the bench can cost you several minutes of searching. The magnetic area holds those screws in position as you remove each component from the board. Lay out screws in the order you removed them, so reassembly follows the same sequence and no fastener ends up in the wrong place. Place the mat on a flat surface before you start, because a tilted table lets small parts slide off the magnetic zone. Clear the zone at the end of each job so old screws do not mix with the next device’s hardware. This habit keeps your repair bench organised and cuts the time you spend hunting for parts on a busy day.

Antistatic Surface and Safe Board Handling

Electrostatic discharge can damage sensitive ICs before a fault shows up on the device, so a controlled work surface matters. The antistatic finish gives you a safer place to set boards while you test, clean, or inspect a section. Set the board on the mat rather than a bare plastic table, especially when you work on exposed chips. For the best protection, pair the mat with a grounding wire and a wrist strap connected to a proper earth point. The antistatic feature supports careful handling, but it does not replace a complete ESD routine on your bench. Keep metal tools and loose cables clear of the working board so nothing bridges a contact by accident.

Heat Limits, Soldering Use, and Size

The rated heat resistance of about 120 to 150°C means the mat handles warmth but not direct contact with a hot iron tip. Keep the soldering iron in its stand while you work, and set hot components onto a heat-safe tray. The mat suits holding boards during inspection and cleanup stages, where surface warmth stays within that range. At 51.5 x 36.5 cm and about 4 mm thick, it covers a standard repair bench without crowding your tools. It weighs 0.89 kg, so it stays stable on the table yet moves easily between benches. The manufacturer also lists it for drone repair work, where a magnetic surface helps you manage small fasteners.

Additional information
Weight0.89 kg
Q & A
Please login to post questions

Key Features

  • Magnetic zone for screws and small steel parts
  • Antistatic surface finish
  • Heat resistance about 120–150°C
  • Working area 51.5 x 36.5 cm
  • Thickness about 4 mm
  • Weight 0.89 kg
  • Blue colour
  • Designed for phone and drone repair work

Specifications

BrandMECHANIC
ModelV70
CategoryRepair Mats
CompatibilityUniversal, not device-specific
TechnologyAntistatic surface, magnetic work area, heat resistance about 120–150°C
Dimensions51.5 x 36.5 cm, about 4 mm thick
Weight0.89 kg

Common Repair Uses

  • Verified workflows where the magnetic and antistatic surface applies.
  • Holding phone screws during disassembly
  • Organising parts across each stage of a mobile repair
  • Supporting board inspection and cleanup on an antistatic surface
  • Setting boards down during soldering prep, with the iron kept in its stand
  • Managing small fasteners during drone repair
  • Organising a general electronics bench

Compatible Devices

  • Universal, not device-specific. The verified scope covers general electronics bench work, phone repair, and drone repair.
  • Universal general electronics bench surface
  • Mobile phone repair work
  • Drone component repair

FAQ

What is the product name?
The product name is MECHANIC V70 Magnetic Heat Resistant Repair Mat.
What is the brand of this product?
The brand of this product is MECHANIC.
What is the model of this product?
The model of this product is V70.
What is this product used for?
This product is used as a magnetic, antistatic work surface for mobile and electronics repair.
Which devices are compatible with this product?
This product is universal and not device-specific, suitable for general electronics bench work.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the heat resistance of this mat?
The mat is rated for about 120 to 150°C, so hot iron tips should rest on a stand, not on the surface.
Is this mat antistatic and magnetic?
Yes, the mat has an antistatic surface and a dedicated magnetic area for holding screws and small metal parts.