Haina H-7007 180W Die Grinder with Flexible Shaft
₨ 6,000
Haina H-7007 180W Die Grinder with Flexible Shaft
The Haina H-7007 is a corded 180W rotary tool kit for technicians who need control on small parts. It runs on 220–240V supply and reaches a no-load speed of 8000 to 30000 rpm, so you can move from light polishing to faster cutting. The collet accepts bits up to 3.2mm. The flexible shaft lets you work at angles a fixed handpiece cannot reach. It suits shaping, grinding and cleaning small metal components where a larger grinder would remove too much material.
In stock
Haina H-7007 Die Grinder for Precision Work on the Repair Bench
The Haina H-7007 die grinder gives your repair bench a compact corded rotary tool for detailed work. A 180W motor drives a collet rated for bits up to 3.2mm, which suits polishing and grinding jobs where an angle grinder would remove too much material. Your workflow benefits most when the job needs control rather than raw power. The speed range runs from 8000 to 30000 rpm, so you set a slow speed for delicate surfaces and a faster one for cutting. This tool fits casing trim, small bracket shaping and surface cleaning on phone components.
Power and Speed Range
The unit has a rated input of 180W at 220–240V. No-load speed spans 8000 to 30000 rpm. A lower speed keeps heat down on thin metal, while a higher speed suits cutting. Start at a moderate setting with each new bit and increase only when the material holds its shape. Confirm your supply voltage before connecting, because the rated range covers 220–240V only.
Collet Capacity and Bit Selection
The maximum shank diameter is 3.2mm. Match each bit shank to the collet before tightening. An undersized shank causes wobble and reduces accuracy on fine work. Polishing points and small burrs are the usual choice for phone component work. Replace any bit that shows chatter, because it leaves uneven marks on the surface.
Flexible Shaft Handling at the Bench
The kit includes a flexible shaft, which lets you hold the handpiece like a pen while the motor sits on the bench. Keep the shaft in gentle curves, since sharp bends stress the cable and slow rotation. Let the tool reach full speed before touching the work. Keep your grip light so the bit does the cutting.
Where This Tool Fits in Your Workflow
Use this die grinder for trimming plastic housing edges, shaping small metal brackets, polishing contact surfaces and cleaning oxidation off small parts. It does not replace a soldering station or hot air rework setup, so keep those tools in your workflow for component-level repair.
| Weight | 2.0 kg |
|---|
Key Features
- ✓180W rated input power
- ✓No-load speed range of 8000–30000 rpm
- ✓3.2mm maximum collet capacity
- ✓Flexible shaft included
- ✓Corded 220–240V operation
Specifications
| Brand | HAINA |
|---|---|
| Model | H-7007 |
| Category | Power Tools, Grinders |
| Compatibility | Universal, not device-specific |
| Technology | Corded electric, flexible shaft |
| Input Voltage | 220–240V |
| Power Rating | 180W |
Common Repair Uses
- ✓Trimming plastic casing edges on phone housings
- ✓Shaping small metal brackets and frames
- ✓Polishing contact surfaces and metal trims
- ✓Cleaning oxidation off small metal parts
Compatible Devices
- ✓Universal, general-purpose rotary tool, not device-specific
- ✓Bits with shank up to 3.2mm (collet capacity)
- ✓Flexible shaft handpiece (included in kit)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the maximum bit size for the Haina H-7007?
What speed range does the Haina H-7007 run at?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



