Relife RL-113 5-Inch Precision Diagonal Cutter
₨ 350
Relife RL-113 Precision Cutter
The Relife RL-113 is a 5-inch precision diagonal cutter for mobile repair work on crowded boards. Its quenched cutting edge shears fine wire, component leads, insulating sleeves, nylon ties and tape with a flat, sharp cut. A spring rebound reopens the jaws after every cut, and the non-slip handle keeps your grip steady through long bench sessions. High-strength steel construction holds up to repetitive trimming in a busy workshop. Pair it with your soldering station, microscope and PCB holder to handle lead trimming and jumper wire cuts on dead phone and charging issue boards. Mechanicpk lists the RL-113 for technicians and service centers across Pakistan.
In stock
Precision Diagonal Cutter for Mobile Repair: Relife RL-113 Overview
The Relife RL-113 is a 5-inch precision diagonal cutter for mobile repair benches that handle fine wire, component leads and insulating sleeves every day. Relife builds the RL-113 from high-strength steel with a quenched cutting edge, and a spring return opens the jaws after each cut so you can work one-handed at speed. Mechanicpk lists it for technicians who already know that a general-purpose hardware plier crushes insulation and bends leads instead of shearing them. If you trim leads beside a BGA IC, cut wire on a charging flex, or clear nylon ties from inside a service-center board, this cutter matches the job class it targets.
Cutting Edge Geometry and Steel
The jaw design drives the RL-113’s value. A diagonal profile sets the cutting edge at an angle to the handle axis, so the jaws reach into a crowded PCB area and sever a lead close to the solder joint. Relife quenches the edge, which raises hardness and keeps the cut face flat and clean. A flat cut matters on a repair board: a ragged stub snags insulation and risks touching a neighbouring pad. Distributor listings describe the body as high-strength steel, and the flat, sharp edge handles fine copper and component leads without fuss. The spring return removes the need to pry the jaws open with your other hand, so that hand stays free to steady the board or hold a PCB holder. The non-slip handle grips firmly during long sessions and keeps repetitive trimming controlled. At 5 inches, the tool balances reach and leverage: long enough to clear taller components, short enough to stay precise.
Where the RL-113 Fits in Your Repair Workflow
Board-level repair involves more cutting than most technicians admit. You trim leads after a soldering station pass, cut wire to length for jumper lagana on a dead phone board, clear insulating sleeves when you replace a damaged battery or charging flex lead, and remove nylon cable clips and ties that block access to a hardware fault. The RL-113 covers all of these cuts with one tool. Listings also describe it as suitable for holding the nickel sheets on mobile phone batteries, which adds a second use during battery work. Place it beside your hot air station and multimeter: cut the lead, check continuity, then move to the next step without switching tools. Under a microscope, the narrow diagonal jaws let you see the cut point and place the edge accurately before you close the handle.
Buying Guidance for Repair Shops and Service Centers
Keep the RL-113 for fine work. Fine wire, component leads, sleeves, ties and tape suit it well; thick cable and hardened wire call for a heavier cutter. Repair shops that run several benches usually keep one cutter at each station next to the soldering station and PCB holder, which removes tool-sharing delays during busy hours. If you build out a complete bench, the same workflow continues with multimeters, microscopes, reballing kits and test boxes, then moves up to ISP pinout tools, eMMC programmers and UFS adapters for software-side repairs. A precision cutter costs little compared with those tools, yet it touches nearly every hardware job on the bench. Order the Relife RL-113 from Mechanicpk and add a reliable diagonal cutter to your next repair workflow.
| Weight | 0.1 kg |
|---|
Key Features
- ✓5-inch compact diagonal body for tight board access
- ✓Quenched cutting edge for flat, sharp cuts
- ✓High-strength steel construction
- ✓Automatic spring rebound reopens the jaws after each cut
- ✓Comfortable, non-slip handle
- ✓Sharp jaws cut wire, insulating sleeves and tape neatly
- ✓Suits nylon cable clips, cable ties and component leads
- ✓Holds battery nickel sheets during battery work
Specifications
| Brand | Relife |
|---|---|
| Model | RL-113 |
| Category | Diagonal Cutting Pliers / Mobile Repair Hand Tools |
| Compatibility | Universal hand tool, not device-specific |
| Supported Devices | Universal, not device-specific |
| Material | High-strength steel with quenched cutting edge |
| Dimensions | 5 inch |
Common Repair Uses
- ✓Trimming and cutting tasks on mobile repair benches, based on the verified cutting function of the tool.
- ✓Trimming component leads during board repair
- ✓Cutting fine wire to length for jumper wire work
- ✓Cutting insulating sleeves
- ✓Removing nylon cable clips and cable ties
- ✓Cutting tape during disassembly and rework
- ✓Holding battery nickel sheets
- ✓Trimming leads after soldering
- ✓General workshop wire cutting
Compatible Devices
- ✓Universal hand tool. It works on any phone, tablet or board where fine wire or lead cutting applies, and it has no device-specific limits.
- ✓Universal, not device-specific
- ✓Android smartphone motherboards (lead and wire trimming)
- ✓iPhone series boards (lead and wire trimming)
- ✓Tablet and feature phone PCBs
- ✓Phone battery flex and nickel sheet work
- ✓Charging flex and connector lead work
- ✓Small electronic modules
- ✓General electronics repair benches
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the Relife RL-113 cut jumper wire on a dead phone board?
What can the Relife RL-113 cut, and what should I avoid cutting with it?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



