Koocu KC-BL041 Hand Finish Blade Set for Underfill Removal
₨ 1,399
Koocu KC-BL041 Underfill Blade Kit
The Koocu KC-BL041 underfill removal blade set gives your repair bench one handle and four blades for board-level glue work. You separate the CPU from the NAND flash, lift CPU glue, trim side glue along IC edges, and cut black underfill without hurting the motherboard. The sandblasted alloy handle with its oxide-coloured finish keeps the tool compact and easy to control during delicate work. Add it beside your hot air station, PCB holder, and microscope to clear glue before IC change, reballing, or memory work on dead phones and hardware fault boards.
In stock
Underfill Removal Blade Set for Mobile Motherboard Glue Work
The Koocu KC-BL041 is an underfill removal blade set built for the glue-clearing stage of board-level mobile repair. One handle carries four blades, and each blade matches a job you meet on CPU and NAND boards: separating the CPU from the NAND flash, lifting CPU glue, clearing side glue, and cutting black underfill without hurting the motherboard. If you buy tools for a workshop that handles stacked-chip boards every day, this kit covers the whole glue sequence in a single hand tool.
How the Four Blades Divide the Work
CPU glue, side glue, and black underfill behave differently under a blade, so one edge rarely handles all three well. The KC-BL041 solves that by giving you a dedicated blade for each condition. The first blade separates the CPU from the NAND flash where the two sit bonded together. The second blade strips glue from the CPU and the surrounding IC area. The third blade works as a professional side glue remover and trims adhesive along IC edges that a wider scraper cannot reach. The fourth blade cuts through black underfill while you protect the traces and pads beneath it. You pick the blade after you inspect the glue under the microscope, and you keep one handle on the bench instead of a drawer of mismatched scrapers.
Where It Fits in Your Board-Level Workflow
Glue removal comes first in most CPU and NAND jobs, before any IC change karna, reballing, or reflow step. On a dead phone or a hardware fault that traces back to a bonded CPU and NAND area, you clear the underfill first so heat and tools reach the chip cleanly. Many technicians pair this underfill removal blade set with Hot Air Stations to soften stubborn adhesive, PCB Holders to lock the board in place, and Microscopes to watch every cut. Once you free the IC, Reballing Kits take over the next stage. When the same board needs a memory read, write, or ISP check, your eMMC Programmers, ISP Pinout Tools, and UFS Adapters work on a board you already cleaned. Keep Test Boxes and Multimeters close to confirm continuity after the glue comes off and before you close the phone.
Koocu KC-BL041 Hand Finish Blade: Build and Buying Notes
The handle follows a special finishing process. Sandblasting gives the alloy surface a fine frosted texture, and a current treatment forms a coloured oxide layer on the metal. You get a textured handle that sits steady in your fingers during slow, controlled cuts. The package contains 1 handle and 4 blades, so a repair shop receives the full glue-clearing sequence in one purchase, and the model code KC-BL041 lets you reorder the same set later without guesswork.
This is a manual metal tool, so your technique sets the result. Work in short, shallow passes, keep the blade angle low, and stay clear of pads and solder mask while you cut. Repair shops that run a rework station gain the most from keeping a dedicated underfill tool on the same bench, because it removes the guesswork from the step that most often damages a board. If your daily work includes CPU and NAND separation, side glue cleanup, and underfill cutting, this blade set gives you a specific tool for each task at a workshop-friendly size.
| Weight | 0.12 kg |
|---|
Key Features
- ✓Package of 1 handle and 4 blades
- ✓Separate blade for CPU and NAND flash separation
- ✓Blade for CPU glue removal on motherboard ICs
- ✓Professional side glue removal blade
- ✓Blade for cutting black underfill glue without hurting the motherboard
- ✓Sandblasted alloy surface with fine frosted texture
- ✓Oxide-coloured metal finish on the handle
- ✓Compact hand tool for bench-level precision work
Specifications
| Brand | Koocu |
|---|---|
| Model | KC-BL041 |
| Category | Hand Tools / Opening Tools |
| Compatibility | Universal hand tool, not device-specific |
| Material | Metal (alloy handle with sandblasted, oxide-coloured finish) |
Common Repair Uses
- ✓Glue clearing and separation work on mobile phone motherboards
- ✓Separating the CPU from the NAND flash
- ✓Removing CPU glue from motherboard ICs
- ✓Removing side glue along IC edges
- ✓Cutting black underfill glue without hurting the motherboard
- ✓Clearing glue before IC change or reballing
Compatible Devices
- ✓Universal hand tool — not device-specific; used on any mobile motherboard that carries glued or underfilled ICs
- ✓Mobile phone motherboards with glued CPU ICs
- ✓Boards where CPU and NAND flash sit bonded together
- ✓Boards with black underfill glue around ICs
- ✓Boards with side glue along IC edges
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How many blades come in the Koocu KC-BL041 set?
Can the KC-BL041 cut underfill glue without damaging the motherboard?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



