Magma C115 Soldering Iron Tip (Straight)

₨ 2,200

Straight C115 Tip for Board-Level Rework

The Magma C115 soldering tip gives your C115 or T115 compatible handle a straight working end for precise SMD rework on mobile phone boards. The C115 cartridge format builds the heating element and temperature sensor into the tip, so heat reaches the joint quickly and stays steady while you work. Use it for charging port pads, flex connector pads, small passive components and jumper wires on dead phone boards. You replace the whole cartridge instead of a loose bit, which keeps your station setup simple. Confirm that your handle accepts C115 cartridges before you order.

In stock

10 People watching this product now!
Description

Magma C115 Soldering Tip for Precision Mobile Board Repair

The Magma C115 soldering tip is a straight-profile cartridge tip built for fine rework on mobile phone motherboards and other small electronics. It follows the C115 cartridge format used in nano handpieces and nano tweezers, and the supplier lists it as compatible with C115 and T115 stocks and stations. If you already run a C115 handle on your bench, you drop this tip in and keep the same station, controller and workflow. A straight tip gives you a predictable contact angle on every pad you touch, which matters when the pads are small and the board is crowded.

How the C115 Cartridge Format Works

A C115 cartridge combines the heating element and the temperature sensor with the tip in a single unit. The heater sits right at the working end, so the tip reaches working temperature quickly and recovers fast when a joint pulls heat away. You replace the entire cartridge when it wears out, so you never deal with a loose bit, poor thermal contact or an uneven fit inside the handle. The straight orientation keeps the tip in line with the handle axis. That gives you a clear line of sight along the work and a natural pencil grip under the microscope, which helps when you control every movement at pad level.

Where It Fits in a Mobile Repair Workflow

On a hardware fault job, you rarely need heat on a whole IC. You need controlled heat on one pad, one jumper point or one small component. This tip suits that kind of work. You re-tin lifted charging port pads, solder a jumper wire across a broken trace (jumper lagana), replace small capacitors and resistors near the charging circuit and touch up flex connector pads after a display problem repair. On dead phone boards that need IC change karna, you lift the chip with a hot air station, then use this tip to clean and re-tin the pads before you place the new part. Reballing kits and flux handle the BGA side of the job, and the iron tip finishes the surrounding passives and test points. A PCB holder keeps the board steady while you work, and a multimeter confirms continuity once the joint cools.

Compatibility and Tip Care

Magma lists this tip for C115 and T115 compatible handles and stations. The genuine C115 family works with nano handpieces and nano tweezers of the same format, so check your handle’s cartridge type before you buy. Handles built for other cartridge sizes will not take a C115 tip. Keep the tip tinned whenever you set the iron down, wipe it on a clean sponge or brass wool before each joint and avoid pushing the temperature higher than the job needs. Store spare cartridges in a protective case so the working end stays clean and undamaged. These habits extend tip life and keep your joints consistent across a full shift.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • Straight tip profile for a direct, predictable contact angle
  • C115 cartridge format for nano handpieces and tweezers
  • Integrated heating element and temperature sensor
  • Compatible with C115 and T115 stocks and stations
  • Suited to SMD and micro soldering work
  • Fits fine-pitch work under a microscope
  • Full cartridge replacement instead of loose bits
  • Sold as a single tip

Specifications

BrandMagma
ModelC115
CategorySoldering Iron Tips
CompatibilityC115 / T115 compatible handles and stations
TechnologyC115 cartridge system with integrated heater and temperature sensor
Tip TypeStraight

Common Repair Uses

  • Fine soldering and rework on mobile phone boards and small electronics.
  • SMD component soldering and replacement
  • Micro soldering on motherboards
  • Charging port pad repair and re-tinning
  • Jumper wire soldering on broken traces
  • Flex connector pad touch-up
  • Pad cleaning after IC removal
  • Soldering in hard-to-reach areas of a PCB
  • Rework under a microscope

Compatible Devices

  • Universal — the tip is not phone-model-specific and works on any board you rework with a C115 compatible handle.
  • C115 / T115 compatible handles and stations
  • JBC NT115 nano soldering handpiece format
  • JBC NP115 nano tweezers format
  • JBC AN115 nano tweezers format
  • JBC B·NANO station format
  • Android and iPhone logic boards (tool is not model-specific)
  • Small electronics PCBs

FAQ

What is the product name?
The product name is Magma C115 Soldering Iron Tip (Straight).
What is the brand of this product?
The brand of this product is Magma.
What is the model of this product?
The model of this product is C115 (straight).
What is this product used for?
This product is used for precision soldering and rework of SMD components, pads and jumper points on mobile phone boards and small electronics.
Which devices are compatible with this product?
This product is compatible with C115 and T115 compatible handles and stations. It is not tied to specific phone models and works on any board you rework.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which handles and stations accept the Magma C115 tip?
The Magma C115 tip fits C115 and T115 compatible handles and stations. The C115 format is used in nano handpieces and nano tweezers such as the NT115, NP115 and AN115 types, so check that your handle takes C115 cartridges before you order.
Can I use this tip in a handle made for C210 or C245 cartridges?
No. C115 is its own cartridge format, so the tip needs a C115 compatible handle. Handles built for other cartridge sizes will not accept it.