2UUL DA22 Hand Finish QUICK Blades Set – Glue Remover

₨ 1,800

2UUL DA22 Blades for Underfill and BGA Glue

The 2UUL DA22 Hand Finish QUICK Blades Set gives Pakistani technicians five hand-ground blade types on an integrated, heat-resistant handle for underfill cleaning, CPU and BGA chip separation, IC removal and glue scraping. The polished high carbon steel springs back without deforming, so you keep a steady cutting line while you work under a package. The supplier lists the handle at about 300°C heat resistance, which suits use beside a hot air station. At 136 x 7 x 10 mm and 9 g net, it stays light on a busy bench. Pair it with hot air stations, microscopes and reballing kits for a complete glue-to-reball workflow.

Out of stock

11 People watching this product now!
Description

2UUL DA22 Hand Finish QUICK Blades Set for Underfill and BGA Glue Work

The 2UUL DA22 Hand Finish QUICK Blades Set covers the part of board repair that hot air alone never finishes: cutting and clearing underfill glue. When black epoxy locks a CPU, eMMC or other BGA package to the PCB, the blade you push under that package decides whether the pads survive or lift. The 2UUL DA22 gives you five QUICK blade types on an integrated handle, so one tool handles chip removal, IC removal, glue scraping, glue cutting and glue removal. You get a ready-to-use handle without sourcing a separate holder, which keeps a busy repair bench simple.

Blade Construction and Handle Design

2UUL grinds these blades by hand from polished high carbon steel plate, and the supplier describes the steel as tough enough to spring back without deforming. That matters when you pry under a package: a blade that bends and stays bent forces you to stop and reshape your angle, while a blade that rebounds keeps your cutting line consistent. The thin, hand-finished edge is the reason technicians choose it for underfill work, because it cuts glue instead of crushing it against the pad.
The handle is integrated into the tool and the supplier lists it at about 300°C heat resistance. Hot air stations routinely run near that range during chip work, so a handle that tolerates the heat keeps your grip steady while you work beside a heated board. The overall tool measures 136 x 7 x 10 mm and weighs 9 g net, so it stays light and compact in your hand and leaves room in a crowded work area under a microscope.

Where It Fits in Your Repair Workflow

Underfill removal sits right after you heat the board and right before you clean and reball. On a dead phone with a suspected eMMC or CPU fault, you warm the package with your hot air station, slide the blade along the glue line, and separate the chip without dragging the neighboring pads. After the chip comes off, the same tool scrapes the leftover glue from the pad area so you can clean with flux and wick, then move to reballing and reflow.
You also reach for it when you need to remove an IC for ISP pinout work. Clearing glue around a storage chip gives you clean access before you solder wires to test points or lift the chip for reading on an eMMC programmer or UFS adapter. A clean pad area saves you time at the next step, whether that step is a boot loop diagnosis, a dead after flash recovery or a straight IC change.
The blades also cut and scrape glue on general mobile phone boards, not just BGA packages. Hardware fault cases like charging issue, display problem or no network issue often end with a glue-covered component that blocks a clean swap, and a hand-finished blade lets you clear that glue without cutting into the board.

Buying Notes for Repair Shops and Distributors

The DA22 suits technicians who handle glue-heavy boards daily and want a dedicated blade set rather than improvising with a scalpel or a screwdriver tip. It pairs naturally with a hot air station, a soldering station, a microscope, a PCB holder and a reballing kit, because each of those tools handles a stage that comes before or after the glue work. If your shop already runs an eMMC programmer, a UFS adapter or ISP pinout tools, this blade set rounds out the mechanical side of the same workflow.
Keep the handle away from direct flame and avoid levering against pads, since hand-ground blades give their best result when you slide them under the glue line with light, steady pressure. Pair the work with a multimeter for continuity checks after cleaning, and check your test box connections before you power the board.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Five QUICK blade types for chip removal, IC removal, glue scraping, glue cutting and glue removal
  • Hand-ground, hand-finished blades built to cut underfill without damaging the board
  • Polished high carbon steel plate that springs back without deforming
  • Integrated handle, ready to use with no separate holder
  • Handle listed for about 300°C heat resistance for use beside a hot air station
  • Suited to cutting bottom-fill black glue
  • Compact 136 x 7 x 10 mm body at 9 g net
  • Suited to prying and scraping on mobile phone PCBs

Specifications

Brand2UUL
ModelDA22
CategoryMobile Phone Repair Blades / Glue Removal Tools
CompatibilityUniversal – not device-specific
MaterialPolished high carbon steel blades
Dimensions136 x 7 x 10 mm
Weight9 g (net)

Common Repair Uses

  • PCB underfill cleaning
  • CPU and BGA chip separation
  • Chip removal
  • IC removal, including storage IC removal
  • Glue scraping around components and pads
  • Glue cutting along the package edge
  • Glue removal before cleaning and reballing
  • General mobile phone repair work alongside a hot air station

Compatible Devices

  • Universal hand tool, not device-specific; suited to mobile phone PCBs with underfill-glued chips
  • Mobile phone motherboards (PCBs) with underfill glue
  • CPU and BGA chips sealed with bottom-fill black glue
  • eMMC and storage ICs (IC hard disk removal)
  • General phone ICs and small chips needing glue removal
  • Boards worked with a hot air station
  • Any brand or chipset family where glue removal is needed (not limited to specific models)

FAQ

What is the product name?
The product name is 2UUL DA22 Hand Finish QUICK Blades Set.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is DA22.
What is this product used for?
This product is used for PCB underfill cleaning, CPU and BGA chip separation, chip and IC removal, and glue scraping, cutting and removal on mobile phone boards.
Which devices are compatible with this product?
This product is a universal hand tool and is not device-specific. It suits mobile phone PCBs where underfill glue covers chips or ICs.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can the 2UUL DA22 remove black underfill glue from a CPU or eMMC?
Yes. The supplier lists the DA22 for cutting bottom-fill black glue and for CPU and BGA chip separation, and the blades cover glue scraping, glue cutting and glue removal.
Is the DA22 handle safe to use with a hot air gun?
The supplier lists the integrated handle at about 300°C heat resistance and designs it for use alongside a hot air gun during mobile phone repair.