2UUL SC15 Deoxidation Soldering Paste 15ml – PCB Flux

₨ 999

Deoxidation Paste for Clean PCB Solder Joints

The 2UUL SC15 Deoxidation Soldering Paste 15ml removes oxidation from PCB pads, CPU pads and old solder joints before you tin, reball or micro-solder. You apply a small amount, heat it with your soldering iron, and the paste lifts the oxide layer so fresh solder wets the surface properly. The low-smoke formula keeps your bench air cleaner during long sessions, and the paste leaves no visible residue once you wipe it off. The compact 15ml tube suits mobile motherboard repair, dock connector prep and chip reballing work. Mechanicpk supplies the 2UUL SC15 to repair shops and technicians across Pakistan.

In stock

14 People watching this product now!
Description

2UUL SC15 Deoxidation Soldering Paste 15ml for PCB Pad Preparation

The 2UUL SC15 Deoxidation Soldering Paste 15ml is a deoxidation soldering paste for mobile repair benches that need clean, wettable surfaces before any solder touches the board. Oxidation on PCB pads, CPU pads and old solder joints stops solder from wetting, and that single problem sits behind a large share of cold joints, failed reflows and repeat jobs. 2UUL builds the SC15 as a paste-type deoxidizer in a 15ml tube, so you place it exactly where the oxide sits instead of flooding the whole board. Mechanicpk supplies it to repair shops and service centers across Pakistan that run daily board-level work.

How the SC15 Paste Fits a Board-Level Repair Workflow

Deoxidation comes before tinning, reballing and component placement in a standard PCB repair sequence. You apply a small amount of SC15 to the oxidized pad or joint, spread it with a brush or cotton swab, and heat the area with your soldering iron. The heat activates the paste, the oxide layer lifts, and you wipe the excess away before you start soldering. The result is a bright, receptive surface that accepts fresh solder, which speeds up tinning and improves how solder paste grips the pad. Skip the step and you fight the board: solder beads up, joints turn grainy, and a pad that looks fine under the microscope lifts on the second pass. Technicians who handle motherboard repair, charging port replacement and micro-soldering use this step to stop dull, balled-up solder that refuses to flow. Pair the paste with a temperature-controlled soldering station or a hot air station from the Mechanicpk range, and you control the heat around neighboring components while the paste does its job.

Technical Highlights of the 2UUL SC15 Formula

2UUL designed the SC15 as a low-smoke formula. That cuts the fumes you breathe during long bench sessions and makes close-up work under a microscope more comfortable. After you wipe the area, the paste leaves no visible residue, so your pads stay ready for the next step and you spend less time scrubbing with IPA. Because the paste holds its place on the pad, you control the amount with a toothpick or a fine brush and avoid spreading flux across nearby ICs and connectors. The tube measures 30mm × 19mm × 107mm, holds 15ml and weighs 18g net, so it fits a bench tray, a toolbox drawer or a pocket for on-site jobs. The manufacturer lists PCB repair, chip reballing and micro-soldering as its applications. SC15 targets oxidation spots on solder joints and does not act as a solder alloy itself. That distinction matters: the paste prepares the surface, and you still need solder wire, solder paste or reballing stencils to build the joint.

Where Technicians Use It in a Pakistani Repair Shop

Oxidation shows up in predictable places on a busy bench. A dead phone with water damage often carries dull or green pads around the charging IC and the dock connector. A charging issue after a rough port replacement can trace back to pads that never wetted properly. A hardware fault found during boot loop diagnosis often ends with reballing a CPU or eMMC, and clean pads decide whether the new balls hold. SC15 helps in each case: clean the pads, tin them, then move to your reballing kit, stencil and PCB holder. Check continuity with a multimeter and inspect the board under a microscope to catch bridges before you power it on. Pad health also decides how many times you can rework a board, so a clean prep step protects your margin on every repeat job. Shops that stock the paste next to ISP pinout tools, eMMC programmers, UFS adapters and test boxes cover both the software and the hardware side of dead-phone recovery. Order the 2UUL SC15 from Mechanicpk and keep one tube at every bench that handles board-level work.

Additional information
Weight0.71 kg
Q & A
Please login to post questions

Key Features

  • Removes oxidation from PCB pads and solder joints
  • Low-smoke formula for more comfortable bench work
  • Leaves no visible residue after wipe-off
  • Improves solder wetting and joint stability
  • Paste form for targeted application with a brush or swab
  • 15ml tube with 18g net weight
  • Compact 30mm × 19mm × 107mm body for bench or on-site use
  • Rated by the manufacturer for PCB repair, chip reballing and micro-soldering

Specifications

Brand2UUL
ModelSC15
CategorySoldering Paste / Deoxidation Flux
CompatibilityUniversal – not device-specific
Supported DevicesMobile phone motherboards and general electronic PCBs
TechnologyDeoxidation paste, low-smoke formula
MaterialPlastic tube
Net Content15ml
Dimensions30mm × 19mm × 107mm
Weight18g (net)

Common Repair Uses

  • Removing oxide spots from PCB pads and solder joints
  • Mobile phone motherboard repair
  • Preparing pads for tinning
  • Chip reballing preparation
  • Micro-soldering on fine-pitch pads
  • Cleaning dock connector pads before soldering
  • Improving solder paste adhesion on aged pads
  • Cleaning CPU pads after removal

Compatible Devices

  • Universal deoxidation paste, not tied to a specific phone model or chipset
  • Mobile phone motherboards
  • Electronic product PCBs
  • Charging port and dock connector pads
  • CPU and BGA chip pads
  • Oxidized solder joints
  • Pads prepared for chip reballing
  • Micro-soldering joints
  • Pads that need tinning before solder paste application

FAQ

What is the product name?
The product name is 2UUL SC15 Deoxidation Soldering Paste 15ml.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is SC15.
What is this product used for?
This product is used for removing oxidation from PCB pads and solder joints before tinning, chip reballing and micro-soldering.
Which devices are compatible with this product?
This product is universal and not device-specific. It works on mobile phone motherboards and general electronic PCBs.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How do you use 2UUL SC15 paste on an oxidized solder joint?
Apply a small amount to the oxidized point, spread it with a brush or cotton swab, heat the area with a soldering iron, then wipe off the excess before you solder.
Does the 2UUL SC15 paste leave residue after soldering?
Distributors describe SC15 as leaving no visible residue after use. Wipe the area after heating to keep the pads ready for the next step.