YCS 3S UV Curing Transparent Mask for Mobile Repair

₨ 500

UV Curing Transparent Mask for Phone Boards

The YCS 3S UV Curing Transparent Mask hardens in about 3 seconds under UV light, so you lock jumper wires, tail plugs and screw posts in place without waiting on slow-drying glue. This transparent UV solder mask insulates and protects components after soldering, and it repairs peeling or partly damaged solder mask on a phone PCB. The clear finish keeps pads and traces visible while you work under the microscope. Mechanicpk supplies it to repair shops and service centers across Pakistan that handle jumper work, charging port repairs and board-level fixes every day.

Out of stock

19 People watching this product now!
Description

YCS 3S UV Curing Transparent Mask for Board-Level Repair

The YCS 3S UV Curing Transparent Mask gives technicians a UV curing transparent mask that sets in roughly 3 seconds, and that speed changes how you finish a board after soldering. Instead of waiting on slow-drying adhesive or leaving a jumper wire floating, you place the resin, hit it with UV light, and move to the next fault. The clear finish keeps pads, traces and wire routing visible, so you can check your work under the microscope before you close the phone. This UV curing transparent mask also suits phone service centers that want one dependable consumable for jumper work, tail plug repair and solder mask patching. Mechanicpk stocks this mask for repair benches across Pakistan that handle dead phone, charging issue and hardware fault jobs every day.

Where the 3-Second Cure Fits in Your Repair Workflow

The curing step sits at the end of soldering, right after you clean the flux residue and confirm the joint. YCS 3S hardens under UV light in about 3 seconds, so the board leaves your fixture within moments instead of sitting idle while glue dries. The mask cures without dead angle, which means resin that flows around a wire or a connector edge hardens together with the surface layer. Technicians use it to secure jumper wires on lifted pads, anchor charging tail plugs, hold screw posts that lost their grip, and fix enamelled wire in position. Each of those jobs needs a bond that stays rigid while you handle the board, and a fast cure gives you that rigidity without the wait. A UV curing lamp is the only extra tool the step needs on your bench, so a small shop can add this mask to its workflow without new equipment. Apply a thin, controlled bead, cure it, and check that the part no longer moves when you press it with tweezers. If the part shifts, add a second small bead and cure again. Short, repeated cycles give you more control than one thick layer.

Protection, Insulation and Solder Mask Repair

Beyond holding parts in place, the mask restores protection on the board. After you rework a joint, the cured layer insulates and protects the components and exposed solder around it. When the factory solder mask has peeled or chipped near a pad, you coat the damaged patch and cure it to cover the bare area again. Jumper wire pads stay anchored and chips stay fixed, and the cured layer resists high temperatures without softening, which matters when you return to the same board with a hot air station for a second pass. Pair the mask with a precision soldering station, a hot air station and a stable PCB holder, so every step from desoldering to curing stays controlled and repeatable.

Why Technicians Pick the Transparent Version

YCS offers this mask in several colors, including transparent, beige and green. The transparent version suits repairs where you want to see the PCB underneath the cured layer. That covers jumper routes you may need to trace again later, pads you want to inspect after curing, and boards where a colored coating would hide the repair from the next technician. In a busy repair shop, consistency matters as much as speed. Shops that repair boards in volume keep a microscope and a multimeter beside the UV lamp and follow one sequence: inspect, test continuity, then cure. You lock the fix only after the circuit tests correct, which cuts rework and protects your repair warranty. For jobs that involve ball replacement on a lifted chip, a reballing kit covers the BGA side of the work, and this mask secures the surrounding wiring once the chip sits back on the board. You finish the job with a clean, protected repair that survives handling, testing and delivery back to the customer.

Additional information
Weight0.15 kg
Q & A
Please login to post questions

Key Features

  • Cures in approximately 3 seconds under UV light
  • Transparent finish keeps pads and traces visible
  • Cures without dead angle around wires and edges
  • Fixes jumper wires, tail plugs, screw posts and pads
  • Insulates and protects components after soldering
  • Repairs peeling or partly damaged PCB solder mask
  • Resists high temperatures and does not soften when cured
  • Also sold in beige and green for different board looks

Specifications

BrandYCS
CategoryUV Glue / Solder Mask (Repair Consumables)
CompatibilityUniversal, not device-specific
TechnologyUV light curing, approximately 3-second cure

Common Repair Uses

  • Real board-level repair scenarios
  • Fixing jumper wires after pad repair
  • Securing charging tail plugs
  • Re-fixing loose screw posts
  • Anchoring enamelled wire on lifted traces
  • Patching peeled or damaged PCB solder mask
  • Insulating and protecting components after soldering
  • Holding pads and chips firmly in place after rework
  • Finishing dead phone and charging issue board repairs

Compatible Devices

  • Universal board-level use, not tied to specific phone models
  • Android smartphone motherboards
  • iPhone logic boards
  • Tablet motherboards
  • Charging tail plug and charging port areas on phone boards
  • Screw post and mounting point areas on phone PCBs
  • Jumper wire routes and lifted pad areas
  • Chip and BGA IC edge areas that need wire or component fixing
  • General PCB areas with peeled or damaged solder mask

FAQ

What is the product name?
The product name is YCS 3S UV Curing Transparent Mask.
What is the brand of this product?
The brand of this product is YCS.
What is this product used for?
This product is used for fixing jumper wires, tail plugs and screw posts on phone boards, and for repairing damaged PCB solder mask.
Which devices are compatible with this product?
This product works on phone and tablet PCBs in general. It is universal and not tied to specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How long does YCS 3S take to cure?
It hardens in approximately 3 seconds when you expose it to UV light.
Does this mask cure without a UV lamp?
No. The mask hardens under UV light, so you need a UV curing lamp on your repair bench.
Can I use it to secure jumper wires after repairing a lifted pad?
Yes. Technicians use it to fix jumper wires, welding pads and enamelled wire in place, and the cured layer resists high temperatures without softening.