2UUL RS138 Red Skull Solder Paste 138℃ 50g
₨ 1,200
138℃ Red Skull Solder Paste for BGA Reballing
The 2UUL RS138 solder paste gives technicians a 138℃ low-melting option for BGA stencil reballing and board-level soldering. 2UUL builds the Red Skull range around clean joints. The RS138 grade targets no false welding, low residue, good conductivity and oxidation resistance. The 50g pack suits a working bench: you refill your syringe, load your stencil and reball without hunting for a second tube mid-job. Pick RS138 when the board around your target IC carries parts that dislike heat, and step up to the 148℃, 183℃ or 199℃ grades when your job calls for them. Mechanicpk supplies it across Pakistan for repair shops, service centers and independent technicians who want a dependable low-temperature paste on hand.
In stock
2UUL RS138 Solder Paste: 138℃ Low-Melt Paste for Board-Level Repair
The 2UUL RS138 solder paste from the Red Skull series gives your bench a 138℃ option for reballing and fine soldering. Mechanicpk stocks the 50g pack for technicians who want a lower melting point than the 148℃, 183℃ and 199℃ grades in the same range. If you run BGA stencil reballing, chase a hardware fault on a dead phone, or handle IC change karna jobs on boards packed with heat-sensitive neighbours, a 138℃ paste gives you more margin on your hot air settings. This page covers what 2UUL verifies for the paste, where it fits in your workflow, and which tools to pair with it.
What 2UUL Lists for the Red Skull RS138
2UUL positions the RS138 for BGA stencil reballing. The supplier descriptions credit it with no false welding, low residue, good conductivity, no cleaning step and oxidation resistance. Each claim maps to a real bench problem. A cold or false joint under a BGA IC brings the phone back with the same charging issue or boot loop issue you just repaired. Heavy residue forces a cleaning pass under a microscope and slows your queue. Oxidation resistance helps the paste wet pads cleanly when you reball. The pack holds 50g, which covers repeated stencil work before you reorder.
Where 138℃ Paste Fits in Your Repair Workflow
Low-temperature paste earns its place in the reball and rework stages. You remove the faulty IC with your hot air station, clean the pads with your soldering station, then apply paste through the stencil and reflow it so the balls form on the IC or board. A lower melting point shortens the time your hot air sits on the board. On a dense logic board, nearby connectors, flex sockets and small passives sit close to your target. Less heat near those parts protects your repair and lowers the chance of a second fault after you hand the phone back.
You will use the RS138 most on three jobs: reballing BGA ICs through a stencil, repairing lifted or damaged pads, and refitting SMD components during a board repair. Hold the board steady in a PCB holder and work under a microscope so you see the paste form clean spheres. After reflow, check continuity with your multimeter before you power the board.
Choosing RS138 Over the Higher-Temperature Red Skull Grades
The Red Skull family ships in four melting points: 138℃, 148℃, 183℃ and 199℃. Choose RS138 when your priority is protecting heat-sensitive parts around the repair. Step up to a higher grade when your job calls for a joint built at a higher melting point. Many technicians keep two grades at the bench and match the paste to the board in front of them. Buy the 50g RS138 for your low-heat work and a higher grade for your standard reballing.
Pair It With the Right Bench Tools
Paste alone does not finish a reball. You need a stable hot air station, a soldering station for pad cleanup, a matching reballing kit with stencils, a PCB holder, and a microscope to inspect every joint. If you work with ISP, eMMC or UFS repair, you also need clean pads under the IC before you place the chip, and a fresh paste layer makes that step repeatable. Browse the matching Mechanicpk categories to complete your setup: Hot Air Stations, Soldering Stations, Reballing Kits, PCB Holders, Microscopes and Multimeters.
Keep the paste sealed between jobs and store it away from heat so it stays workable. Mechanicpk ships the 2UUL RS138 solder paste to Karachi, Lahore, Islamabad and the rest of Pakistan, so your next reball does not wait on a delayed order.
| Weight | 0.50 kg |
|---|
Key Features
- ✓138℃ low-temperature Red Skull grade
- ✓50g pack for repeated bench use
- ✓Made for BGA stencil reballing
- ✓Targets no false welding
- ✓Low residue after reflow
- ✓Good conductivity
- ✓No cleaning step required
- ✓Oxidation resistance
Specifications
| Brand | 2UUL |
|---|---|
| Model | RS138 (Red Skull) |
| Category | Solder Paste |
| Compatibility | Universal — not device-specific |
| Technology | Low-temperature solder paste, 138℃ melting point |
| Weight | 50g |
Common Repair Uses
- ✓BGA stencil reballing and low-heat board-level soldering.
- ✓BGA stencil reballing
- ✓IC change karna on dead phone boards
- ✓Hardware fault repair under BGA ICs
- ✓Pad repair after IC removal
- ✓SMD component refitting
- ✓Charging issue repair involving IC replacement
- ✓Boot loop issue repair on hardware-faulty boards
- ✓Reball and rework jobs near heat-sensitive parts
Compatible Devices
- ✓Universal — not device-specific. The paste works on any mobile phone or PCB board you reball or solder.
- ✓Mobile phone motherboards, all brands
- ✓BGA ICs reballed through a stencil
- ✓SMD components on logic boards
- ✓PCB pads and lifted pads
- ✓Boards with heat-sensitive neighbouring parts
- ✓Android phone boards
- ✓iPhone logic boards
- ✓General PCB and electronics repair
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the melting point of 2UUL RS138 solder paste?
Do I need to clean the board after soldering with 2UUL RS138?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



