2UUL BA15PS iPhone 15 Plus Back Cover Adhesive
₨ 1
iPhone 15 Plus Back Cover Adhesive
The 2UUL BA15PS Back Cover Sealing Adhesive for iP15 Plus(5pcs/Pack) gives you a pre-cut, double-sided adhesive gasket built for the iPhone 15 Plus rear frame. You peel, align, and press the back glass down without trimming or measuring anything. The adhesive helps restore dust and water resistance after a repair, and the five-piece pack covers five separate back glass jobs on your bench. Repair shops and service centers across Pakistan use it after back glass replacement, board-level work, and battery service. Mechanicpk supplies it with a precise fit for this one model, so every reseal follows the same clean process.
Out of stock
iPhone 15 Plus Back Cover Adhesive for Precise Rear Glass Resealing
The 2UUL BA15PS Back Cover Sealing Adhesive for iP15 Plus(5pcs/Pack) is a pre-cut iPhone 15 Plus back cover adhesive that bonds the rear glass to the frame after you open the phone. 2UUL cuts each gasket to the iPhone 15 Plus rear frame outline, so you skip trimming, measuring, and guesswork. One pack holds five pieces, which covers five separate rear glass jobs. Mechanicpk stocks this adhesive for technicians and repair shops across Pakistan who handle iPhone 15 Plus back glass work and need the same seal quality on every job.
Key Technical Highlights
This product belongs to the double-sided adhesive gasket family, and the BA15PS model targets the iPhone 15 Plus only. The cut-out pattern follows the rear frame, including the opening around the camera area, so the gasket sits flat on the frame edge when you align it. A waterproof adhesive layer bonds the glass to the frame and holds the back cover in place after reassembly.
You get a gasket that matches the frame geometry instead of a roll of generic tape. A roll forces you to cut and join strips by hand, and every joint becomes a potential gap in the seal. A single pre-cut piece removes those joints. That consistency matters when your customer expects the phone to keep its dust and water resistance after the repair.
The adhesive suits the iPhone 15 Plus rear panel design, where you separate the back glass from the frame to reach the internals. The supplier describes the bond as durable and long-lasting, and the pre-cut shape keeps the adhesive width even around the frame.
Where It Fits in the Back Glass Repair Workflow
You reach for this adhesive at the end of a repair, after you finish the work inside the phone. A typical job starts with heat and a cutting tool to separate the old back glass. Then you clean every trace of old adhesive from the frame and the glass, because leftover residue weakens the new bond. A microscope helps you spot small strips of residue along the frame edge, and a PCB holder keeps the phone steady while you clean.
Once the surfaces are clean, you place the BA15PS gasket on the frame, check that the camera cut-out lines up, and press the back glass down. Test the phone before you seal it. Power it on, confirm the display, charging, and network all work, and power it off again. A multimeter and a test box handle quick checks on the way, and you save yourself from opening a sealed phone twice.
The same adhesive step closes out many different jobs: back glass replacement after a crack, battery replacement, and board-level repair such as an IC change on a dead phone or a charging issue. If your bench already runs hot air stations and soldering stations for logic board work, this adhesive completes the workflow by sealing the phone once the hardware fault is fixed. Technicians who use reballing kits for chip-level work on the same device finish the job with this gasket as well.
Why Technicians Choose This Pack
A five-piece pack matches how repair benches actually work. You keep a small stock, use one gasket per phone, and never reuse an old adhesive layer. Reusing a used gasket leaves weak spots, so a fresh piece per job protects your repair quality and your reputation with customers.
This product fits one model, so you pick it with confidence. The BA15PS targets the iPhone 15 Plus and nothing else. If your customer brings in a different iPhone, match the gasket to that exact model before you start the repair. Mechanicpk lists adhesives by model, so you find the right piece without trial and error.
For shop owners, the pack size also simplifies stock planning. Five pieces cover a small batch of repairs, and the compact pack stores easily in a drawer next to your other iPhone repair consumables. Technicians who service iPhone 15 Plus devices on a regular basis keep a few packs on hand and avoid delays when a back glass job arrives.
Pair the adhesive with a clean working surface, steady heat control, and patient alignment. The gasket does its part when the frame and glass are clean, and the final seal depends on how carefully you apply it.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut adhesive gasket made for the iPhone 15 Plus rear frame
- ✓Double-sided design that bonds the back glass to the frame
- ✓Waterproof adhesive layer for resealing after repair
- ✓Helps restore dust and water resistance after repair
- ✓Precision cut that aligns with the rear frame outline
- ✓Easy to apply for fast, clean back glass replacement
- ✓Durable adhesive for long-lasting bonding strength
- ✓Five pieces per pack for multiple professional repairs
Specifications
| Brand | 2UUL |
|---|---|
| Model | BA15PS (5pcs/Pack) |
| Category | Back Cover Sealing Adhesive |
| Compatibility | iPhone 15 Plus |
| Supported Devices | iPhone 15 Plus |
| Technology | Pre-cut double-sided waterproof adhesive gasket |
Common Repair Uses
- ✓Verified workflows where a technician reseals the iPhone 15 Plus back glass.
- ✓Back glass replacement on the iPhone 15 Plus
- ✓Resealing the back cover after a cracked rear glass repair
- ✓Restoring dust and water resistance after opening the phone
- ✓Closing the phone after battery replacement
- ✓Closing the phone after board-level repair
- ✓Replacing a worn or damaged factory seal
Compatible Devices
- ✓Verified compatibility scope is the iPhone 15 Plus only. The adhesive is model-specific, not universal.
- ✓iPhone 15 Plus rear frame and back glass
- ✓Not universal: other iPhone models need their own model-specific adhesive
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the BA15PS adhesive fit other iPhone 15 models?
How many pieces come in one pack, and can you reuse a gasket?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



