2UUL DA13 Non-Slip Blade Handle for Mobile Repair
₨ 800
DA13 Non-Slip Blade Handle
The 2UUL DA13 non-slip blade handle gives you a secure, controlled grip for the repair blades on your bench. 2UUL designed it as a short handle, so your fingers stay close to the cutting edge and you keep fine control during glue removal, underfill cleaning, and chip lifting. The package contains the handle only, so you fit the blade that suits the job. Pair it with your hot air station, microscope, and PCB holder for clean, repeatable board-level work. Mechanicpk supplies the DA13 to technicians, repair shops, and service centers across Pakistan.
In stock
2UUL DA13 Non-Slip Blade Handle for Precision Blade Work
The 2UUL DA13 non-slip blade handle gives your repair blades a stable, controlled grip on the bench. 2UUL supplies it as a handle only, so you fit the blades you already trust for glue removal, underfill cleaning, and chip lifting. This page explains what the DA13 does, where it fits in a board-level repair workflow, and what to check before you order for your shop.
Handle-Only Design and Grip Control
The DA13 does one job: it holds a repair blade without slipping. Slip causes most blade damage on a motherboard. A skidding edge scratches solder mask, lifts pads, and tears fine traces when you scrape underfill or separate a stuck component. A non-slip surface lets you build pressure gradually instead of squeezing harder to compensate, and that keeps the cut predictable.
The short body places your fingertips close to the blade edge. You feel the resistance of cured glue or underfill directly, which helps around dense areas such as the CPU, eMMC, and power IC zones. The secure hold also reduces hand fatigue during long sessions, when you clean several boards in a row.
Check the package before you order. The DA13 ships as a handle only, with no blades inside. You choose the blade profile that matches the task and mount it in the handle.
Where It Fits in Your Repair Workflow
Blade work sits in the middle of most board-level repairs. When you handle a dead phone, a hardware fault after a drop, or a charging issue that traces back to a damaged IC, the sequence usually runs the same way. You secure the board in a PCB holder, preheat with a hot air station, and soften the underfill. Then you cut or scrape with a blade under a microscope. A stable handle makes that cutting step safer for the board.
IC change karna depends on clean separation. Residual glue around a CPU or eMMC makes lifting harder and raises the risk of pad damage, so a controlled blade pays off before you start soldering or reballing. After the chip comes off, you use the same handle to clear leftover adhesive from the pads before you prepare the surface for a reballing kit or fresh solder.
Keep the handle clear of the direct hot air flow as a general bench habit, and rest the blade tip on the board only when you start the cut. These habits protect both the board and the tool, whatever blade you fit.
Buying Notes for Repair Shops
The DA13 suits benches that rotate between several blade types. Many technicians keep one handle per blade profile, so they skip the blade swap in the middle of a job. At this handle-only format, stocking more than one DA13 stays practical for shops that run glue removal, chip lifting, and cleaning at the same time.
Match the blade to the task before you buy. Decide whether you need thin blades for screen and frame work or sturdier blades for underfill and chip removal, then confirm the blade fits the handle. The DA13 handles the grip. The blade you choose handles the cut.
Mechanicpk stocks the 2UUL DA13 for Pakistani technicians who build out a complete board-repair setup. Combine it with soldering stations, hot air stations, microscopes, PCB holders, and reballing kits from the same catalog to cover the full path from teardown to final reassembly.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Non-slip grip for controlled blade handling
- ✓Short design for close control near the blade edge
- ✓Secure hold that resists slipping under pressure
- ✓Ergonomic shape for comfortable extended use
- ✓Durable construction for daily workshop use
- ✓Handle-only package, so you pick the blade that suits the job
- ✓Suits board-level glue removal and chip lifting workflows
- ✓2UUL brand repair accessory
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA13 |
| Category | Mobile Repair Tools – Blades & Handles |
| Compatibility | Repair blades (handle only, blades not included) |
Common Repair Uses
- ✓Holding a repair blade steady for board-level and teardown work
- ✓Underfill and glue removal around CPU, eMMC, and ICs
- ✓Chip lifting after preheating
- ✓Cleaning leftover adhesive from pads before reballing
- ✓Separating glued parts and shields on boards
- ✓Screen-edge and frame adhesive work during disassembly
Compatible Devices
- ✓Universal — not device-specific; the handle holds the blade you fit and works across any board or device that blade work suits
- ✓Android smartphone motherboards
- ✓iPhone motherboards
- ✓Tablet motherboards
- ✓Phone screens and frames during teardown work
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the 2UUL DA13 come with blades?
Can I use the DA13 for removing glue and underfill from a mobile motherboard?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



