Hi6555 V211 Power IC for Huawei HiSilicon Board Repair

₨ 350

Hi6555 V211 Power IC for Mobile Repair in Pakistan

The Hi6555 V211 power IC is a HiSilicon power management IC from the Hi655x family, built for technicians who replace failed PMICs on Huawei and HiSilicon-based boards. It sits on the power path of the board, so a fault here shows up as a dead phone, a missing rail, or a board that never reaches a stable boot. Mechanicpk supplies it as a repair part for IC-level work on your bench. Match the V211 suffix against the marking on the removed chip before you solder the new one.

16 People watching this product now!
Description

Hi6555 V211 Power IC: HiSilicon PMIC for Board-Level Repair

The Hi6555 V211 power IC belongs to the HiSilicon Hi655x power management family. Huawei used these PMICs to feed the application processor and the supporting circuits on its HiSilicon-based boards. A PMIC generates and sequences the supply rails the rest of the board depends on. When it fails, the board gives you little to work with: no power-on response, abnormal current draw, or a phone that dies shortly after it wakes. This part gives you a direct replacement route for that failure, so you fix the cause on the board and skip the guesswork of swapping unrelated components.

What the Hi655x Family Does on the Board

Kernel driver documentation for the Hi655x family describes a multifunction PMIC. It exposes voltage regulators, handles power-key and undervoltage interrupts, and supplies a clock for the WiFi and Bluetooth blocks. The processor talks to it over a dedicated serial signal channel, and the driver reads a version register at start-up. That version register explains why the V211 suffix matters. Your replacement must match the revision the board expects. A different revision of the same family number can change how the chip behaves at power-up, so read the marking on the old IC under your microscope before you order.

Where It Fits in Your Repair Workflow

You reach for a power IC after the cheaper checks are finished. Start with a clean current reading on a bench supply, then check for shorts on the battery line and the main rails with a multimeter. If a rail is missing or a short traces back to the PMIC area, the chip becomes the main suspect. At that point you lift the IC with a hot air station, clean the pads, and inspect them for lifted tracks. Then you place the new Hi6555 V211 and reflow it with controlled heat. Preheat the board from below and use a PCB holder so the board stays flat. Reballing is a separate job. A quality reballing kit helps if you reuse a chip, but a fresh IC arrives ready for placement.

Handling and Fitment Notes for Your Bench

This is a BGA-style surface-mount part, so heat control decides the outcome. Set a moderate airflow, protect neighbouring components with kapton tape, and keep the board from overheating around the CPU area. Under a microscope, check that no solder bridges remain on the pads before you power the board for the first time. Power it through a current-limited supply on the first attempt. If current draw looks normal and the phone boots, run a charging test and a full power-cycle test before you return it. If the fault stays, the problem sits in another stage, and you continue tracing the rails rather than replacing the same chip twice.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • HiSilicon Hi655x-family power management IC
  • V211 revision for like-for-like replacement
  • Supplies regulated rails to the board
  • Supports power-key and undervoltage interrupt handling
  • Supplies a clock for WiFi and Bluetooth blocks
  • Surface-mount BGA-style part for hot air rework
  • Suits IC-level repair on Huawei boards
  • Fits your PMIC replacement stock

Specifications

BrandHiSilicon
ModelHi6555 V211
CategoryMobile Phone Power Management IC (PMIC)
CompatibilityHiSilicon Hi655x-family PMIC; confirm the board marking before fitting
TechnologyPower management IC with voltage regulators, interrupt handling, and WiFi/Bluetooth clock supply

Common Repair Uses

  • Replacing a failed power management IC on HiSilicon-based Huawei boards after the faulty rail is confirmed.
  • Dead phone with no response on power-on
  • Abnormal current draw on the bench supply with no boot
  • Short circuit traced to the PMIC area on the main rails
  • Missing or unstable supply rail after a rail check
  • Charging issue that traces back to the power IC stage
  • Dead after flash where the board never recovers its supply rails
  • Phone that powers off shortly after waking
  • Power-key not responding when the PMIC interrupt path has failed

Compatible Devices

  • HiSilicon-based Huawei boards that use a Hi655x-family PMIC. Confirm the device-level match against the chip marking on your board, because compatibility is board-specific rather than universal.
  • Huawei boards fitted with a Hi6555 V211 marked PMIC
  • HiSilicon-based Huawei handset boards using the Hi655x PMIC family
  • Boards where the removed chip reads Hi6555 with a V211 revision mark
  • Donor-matched replacement jobs where the original chip is verified under a microscope
  • Boards with a confirmed PMIC fault after a rail and short check
  • Honor-branded boards from the same HiSilicon platform, if the marking matches
  • Service-centre boards where power-IC replacement follows a current-draw diagnosis
  • Repair-bench stock for known failing boards of the same PMIC revision

FAQ

What is the product name?
The product name is Hi6555 V211 Power IC.
What is the brand of this product?
The brand of this product is HiSilicon.
What is the model of this product?
The model of this product is Hi6555 V211.
What is this product used for?
This product is used to replace a failed power management IC on HiSilicon-based Huawei boards.
Which devices are compatible with this product?
This product is compatible with HiSilicon-based boards that use the Hi655x-family PMIC. Confirm the Hi6555 V211 marking on your board before fitting.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which faults point to a bad Hi6555 V211 power IC?
A dead phone with no power-on response, abnormal current draw, a short on the main rails, or a missing supply rail points toward the PMIC. Confirm with a multimeter and a bench supply before you remove the chip.
How do I confirm the right Hi6555 V211 revision before soldering?
Read the marking on the removed chip under a microscope and match the Hi6555 name and the V211 suffix. A different revision can change power-up behaviour, so never fit a chip with a different suffix.