2UUL SC88 Non-Magnetic IC Micro-Point Pry Needle Set
₨ 1,500
SC88 Micro-Point Pry Needles for Chip Work
The 2UUL SC88 is an IC micro-point pry needle set built for technicians who lift chips and clear glue on dense phone boards. You get an ultralight carbon fiber handle and two replaceable micro-point needles. The needle tip slips under a hot IC, nudges small parts, and drags tin without gouging pads or neighbouring components. The non-magnetic design keeps loose metal debris off your work area. Mechanicpk stocks the SC88 for Pakistani repair shops that run board-level jobs on iPhone, Android, and tablet motherboards. Pair it with a hot air station and a microscope for controlled, repeatable rework at your bench.
Out of stock
IC Micro-Point Pry Needle Set for Board-Level Rework
The 2UUL SC88 IC micro-point pry needle set fills the gap between a flat spudger and a pair of tweezers. A spudger is too wide for a crowded logic board, and tweezers need clearance you rarely have beside a shield frame or a tall capacitor. The SC88 gives you a fine, elastic needle tip on a light carbon fiber handle, so you control the lift with a fingertip instead of force. Technicians who handle hardware fault jobs every day reach for this class of tool the moment hot air softens the solder and glue under an IC.
How the Micro-Point Tip Works Under Heat
Once your hot air station brings the chip to reflow temperature, the needle tip embeds at the edge of the IC and lifts it clear. The tip flexes instead of snapping, which protects the pads underneath and the parts sitting beside the chip. That behaviour matters on a dead phone with a damaged CPU or power IC, because a slipped tool can strip a pad and turn a simple IC change into a trace repair. Under a microscope, the fine point lets you see exactly where it contacts the board before you commit pressure.
The same tip clears cured underfill and glue around BGA ICs. You work in short, shallow strokes along the chip edge and lift residue in pieces rather than scraping the surface. After the chip is off, you can drag excess tin across the pads to level them before you add flux and reball.
Handle, Balance, and Bench Comfort
The handle uses ultralight carbon fiber. A light handle cuts hand fatigue during long sessions, which matters when a queue of boards with charging issue or display problem faults waits on your bench. The set is compatible with the 2UUL DA29 carbon handle, so you can keep the handle you already use and swap in fresh needles when a tip wears. The non-magnetic build also keeps solder balls and metal dust from clinging to the tool and drifting across the board.
Where the SC88 Fits in Your Repair Workflow
You use the SC88 at three points in a typical board-level job. First, you free the chip from the board after heating. Second, you clear glue and old tin from the pad area. Third, you guide a fine jumper wire into position when you run a fly line to repair a broken trace, the classic jumper lagana step on a damaged pad or connector. Each of these steps sits between your soldering station and your microscope, which makes the SC88 a small tool with an outsized effect on your success rate.
Pair the set with the rest of a proper rework bench. A hot air station handles the heat, a PCB holder keeps the board still, a multimeter confirms the fault before and after the repair, and a reballing kit prepares the chip for reinstall. The SC88 connects those steps by giving you clean control at the contact point where most bench mistakes happen.
Why Repair Shops in Pakistan Choose It
Pakistani workshops run high volumes of iPhone, Samsung, Oppo, Vivo, Infinix, and Tecno boards, and every one of them uses ICs that need careful lifting. An IC micro-point pry needle set costs a fraction of the board you protect with it. Shops that train new technicians also use the 2UUL SC88 pry needle to teach pry control, because the fine tip rewards a light touch and exposes heavy-handed habits quickly. Mechanicpk supplies the SC88 as an IC pry tool for mobile repair in Pakistan, with a handle that fits your existing 2UUL bench tools.
If you are building a full rework station, start with the hot air and soldering stations, add a microscope, and complete the kit with PCB holders, reballing tools, and this micro-point pry set.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Two replaceable micro-point needles
- ✓Ultralight carbon fiber handle
- ✓Elastic fine tip that embeds under chip edges
- ✓Non-magnetic design
- ✓Pries ICs without damaging nearby parts
- ✓Clears chip glue and drags tin
- ✓Compatible with the 2UUL DA29 handle
- ✓Compact package, 15 g net weight
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC88 |
| Category | Prying and Opening Tools |
| Compatibility | 2UUL DA29 carbon fiber handle |
| Material | Ultralight carbon fiber handle |
| Dimensions | Package size 144 x 51 x 11 mm |
| Weight | Net 15 g, gross 22 g |
Common Repair Uses
- ✓Lifting heated chips, clearing glue and underfill, dragging tin, and guiding jumper wires on phone boards
- ✓Lifting an IC after hot air heating
- ✓BGA IC removal on phone motherboards
- ✓Clearing underfill and glue around chips
- ✓Dragging excess tin off pads
- ✓Nudging small SMD components
- ✓Guiding fly line and jumper wires onto pads
- ✓Separating a chip edge under a microscope
- ✓Cleaning pad areas before reballing
Compatible Devices
- ✓Universal hand tool for board-level work, not tied to one device model
- ✓iPhone logic boards
- ✓Samsung Android motherboards
- ✓Oppo and Vivo motherboards
- ✓Infinix and Tecno motherboards
- ✓Other Android phone motherboards
- ✓Tablet motherboards
- ✓BGA ICs on smartphone boards
- ✓2UUL DA29 carbon fiber handle
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use the SC88 to remove a BGA IC from a phone board?
Does the SC88 come with a handle or do I need to buy one separately?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



