1616A0 iPhone 13 U2 Tristar IC for Charging Repair
₨ 300
U2 Tristar Charging IC for iPhone 13
The 1616A0 is the U2 Tristar charging controller on the iPhone 13, 13 mini, 13 Pro and 13 Pro Max logic boards. It handles USB port authentication and controls charging, so a failed unit usually shows up as no charging, unstable charging, or a port that rejects a cable that worked before. Confirm the U2 position and the original part number before you replace it. This chip suits board-level repair work where the technician has a microscope, hot air station and reliable reflow setup.
iPhone 13 U2 IC 1616A0 for Board-Level Charging Repair
The iPhone 13 U2 IC 1616A0 is the U2 Tristar charging chip that distributors list at reference U9300 on the iPhone 13 family’s logic board. It sits in the USB charging path and manages port authentication. When it fails, the phone may charge slowly, stop charging entirely, or reject a cable that worked yesterday. Many technicians mistake this fault for a weak battery and replace the wrong part. Checking the U2 before any swap saves time and protects the customer’s budget. A microscope, a hot air station and steady flux work are the minimum tools for a clean replacement on these boards.
Where the 1616A0 Fits in the Charging Circuit
The U2 Tristar controls the link between the Lightning or USB-C charging path and the power management side of the board. Its job is to verify the connected accessory and then allow or limit power delivery. Because the IC sits between the port and the charging circuitry, a fault here can look like a port problem, a cable problem or a battery problem. Your diagnostic should follow the signal path from the port inward. Start by checking the port and connector, then the charging rails, and only then the U2 itself. Distributors group the 1616A0 with the wider U2 Tristar family, but the part number matters. Listings assign the 1616A0 to the iPhone 13 series, while the 1618A0 is listed for the iPhone 14 series, so always match the number on the board to the number on the chip.
Common Fault Symptoms Technicians Check First
A dead phone that does not respond to a known-good charger deserves a closer look at the U2 before you blame the battery. Typical symptoms include no charging, intermittent charging, a charging issue that appears only with certain cables, and a phone that drains quickly while plugged in. Some boards show the same behavior when the battery is weak, so measure the battery and inspect the port area before you commit to a replacement. A U2 tester or a dedicated Tristar diagnostic tool can show whether the chip responds, which narrows the fault in seconds. Use a multimeter to check for shorts on the charging lines and confirm the rails feeding the U2 are present. If the rails are healthy and the chip responds poorly, the 1616A0 becomes the suspect. Document each reading. That record protects you when a customer asks why you replaced the part.
Replacement Workflow on iPhone 13 Boards
Begin by confirming the original part number and the board revision, because the wrong U2 will leave the phone in the same state. Remove the old IC with a hot air station set to a controlled profile, and protect nearby components with heat shielding. Clean the pads with flux and solder wick until they are flat and free of residue. Align the new 1616A0 by its pin 1 marking and reflow it with steady, even heat. Check for bridged pins under the microscope before you power the board. Power the board through a current-limited supply first, so a remaining short does not damage other parts. After the repair, test charging with a known-good cable and confirm the phone identifies the accessory correctly. Keep your reflow profile consistent across jobs, because consistency is what separates a clean IC swap from a comeback.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Specified for U9300 position on iPhone 13 series boards
- ✓Covers iPhone 13, 13 mini, 13 Pro and 13 Pro Max
- ✓Matched by part number (1616A0), not by generic U2 description
- ✓Suited to microscope and hot air rework workflows
- ✓Supports charging path diagnosis from port to power circuitry
- ✓Clear distinction from the 1618A0 used on iPhone 14 series
- ✓Ideal for technicians who verify before replacing
Specifications
| Model | 1616A0 |
|---|---|
| Category | Mobile Phone ICs |
| Compatibility | iPhone 13 series |
| Supported Devices | iPhone 13, iPhone 13 mini, iPhone 13 Pro, iPhone 13 Pro Max |
| Technology | U2 Tristar USB charging authentication IC |
| Board Reference | U9300 |
Common Repair Uses
- ✓Replacing a faulty U2 Tristar when the phone shows no charging or unstable charging
- ✓Repairing charging faults that appear with some cables but not others
- ✓Board-level IC replacement after a port-area fault has been ruled out
- ✓Verifying U2 status with a Tristar diagnostic tool before ordering a battery
Compatible Devices
- ✓iPhone 13 series (iPhone 13, iPhone 13 mini, iPhone 13 Pro, iPhone 13 Pro Max)
- ✓iPhone 13
- ✓iPhone 13 mini
- ✓iPhone 13 Pro
- ✓iPhone 13 Pro Max
FAQ
What is the product name?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this IC fix a dead iPhone 13 with no charging?
Is the 1616A0 the same as the 1618A0 used on iPhone 14?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



