KADA 850/852 Heat Gun Handle Pipe 3 Wire

₨ 1

KADA 852 Hot Air Gun Handle

This KADA 852 hot air gun handle replaces a faulty handle on KADA 850 and 852-series rework stations. It carries the internal heating element, the temperature sensor, and a 3-wire cable (heater, sensor, ground). The handle works across KADA 850, 852D+, and 858D+ stations, and listings rate it for roughly 100°C to 450°C. At about 180 mm long, it fits SMD rework, IC removal, and PCB repair. You fix a dead hot air gun on your bench by swapping the handle, with no full station purchase. Check your station’s wire count before you order.

Out of stock

15 People watching this product now!
Description

KADA 852 Hot Air Gun Handle for 850/852 Rework Stations

The KADA 852 hot air gun handle gives you a direct fix when the heat gun on your rework station stops heating, loses temperature control, or burns out. It pairs with KADA 850, 852D+, and 858D+ hot air stations and uses a 3-wire cable that carries the heater feed, the sensor signal, and the ground. You replace only the handle, so the main station, its controller, and the airflow pump stay in service. That makes it one of the lowest-cost ways to bring a faulty hot air gun back to work in your shop.

Handle Construction and Technical Profile

The handle combines an internal heating element with a temperature sensor inside a heat-resistant plastic and metal body. The sensor feeds temperature data back to the station, which regulates output up to roughly 450°C. Your station’s own limit sets the working ceiling, so check your model’s range before you set a profile. The body measures about 180 mm, and the cable runs about 70 to 90 cm. That length lets you reach a motherboard on a PCB holder without dragging the station across the bench. Because the heat is delivered through the handle’s pipe, you can change nozzles to match each job.

Where It Fits in Your Rework Workflow

Hot air is the core of any board-level job, and a weak handle ruins every repair that follows it. This handle supports SMD soldering and desoldering, IC removal and replacement, mobile motherboard repair, PCB rework, and heat shrink work. When a customer brings a phone with a hardware fault and you plan IC change karna on a charging IC or a power IC, a stable airflow and a steady temperature decide whether the pads survive. Pair the handle with a quality microscope, a PCB holder, and a reballing kit, and you build a complete rework setup. Stable heat also protects neighboring components from uneven warming.

Matching the Wire Count Before You Order

Hot air handles come in several wire configurations. This one uses 3 wires. Other KADA, M&R, and 858D-style handles use 4, 5, or 6 wires and carry different connectors. Open your station, check the connector and the wire count, and confirm the match before you order. Use a multimeter to test the old handle’s heater coil and sensor continuity first. If the coil reads open, the handle is your fault. If it reads normal, trace the station’s board or fan instead. This check saves you a wrong purchase and a second round of downtime.

Together with your existing hot air station or soldering station, this replacement handle keeps your repair line productive without the cost of a new unit.

Additional information
Weight0.4 kg
Q & A
Please login to post questions

Key Features

  • Internal heating element and temperature sensor in one handle
  • 3-wire cable (heater, sensor, ground)
  • Rated for roughly 100°C to 450°C
  • About 180 mm handle length for steady control
  • Heat-resistant plastic and metal body
  • Fits KADA 850, 852D+, and 858D+ stations
  • Replaces the handle only, so your station stays in service
  • Accepts interchangeable hot air nozzles

Specifications

BrandKADA
Model850/852
CategoryHot Air Gun Handle
CompatibilityKADA 850 / 852D+ / 858D+ hot air rework stations
TechnologyInternal heating element with temperature sensor, 3-wire cable (heater + sensor + GND)
MaterialHeat-resistant plastic and metal
DimensionsHandle length approx. 180 mm; cable length approx. 70–90 cm

Common Repair Uses

  • Replacement of a faulty hot air handle on a rework station
  • SMD component soldering and desoldering
  • IC removal and replacement
  • PCB repair and rework
  • Mobile phone motherboard repair
  • Heat shrink tubing work
  • Electronics prototyping and maintenance

Compatible Devices

  • KADA hot air rework station models (not a phone-specific tool)
  • KADA 850 hot air station
  • KADA 852 rework station
  • KADA 852D+ rework station
  • KADA 858D+ rework station

FAQ

What is the product name?
The product name is KADA 850/852 Heat Gun Handle Pipe 3 Wire.
What is the brand of this product?
The brand of this product is KADA.
What is the model of this product?
The model of this product is KADA 850/852.
What is this product used for?
This product replaces a faulty hot air gun handle on KADA rework stations for SMD soldering, IC removal, and PCB repair.
Which devices are compatible with this product?
This product is compatible with KADA 850, 852D+, and 858D+ hot air rework stations.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How many wires does this hot air gun handle use?
This handle uses a 3-wire cable that carries the heater feed, the temperature sensor signal, and the ground. Handles for other models can use 4, 5, or 6 wires, so check your station’s connector before you order.
What temperature range does this KADA hot air gun handle support?
Distributor listings rate the handle for roughly 100°C to 450°C. Your station’s controller sets the actual working range.