PMI8994 Power IC for MSM8996 Mobile Repair
₨ 200
PMI8994 Power IC for MSM8996 Boards
The PMI8994 power IC is a Qualcomm power management chip that communicates over the SPMI bus. It is commonly found on MSM8996-based boards, where it supplies power to several LDO rails. The chip also includes GPIO, MPP, LPG, and WLED blocks, so a single faulty part can stop more than one subsystem. This listing gives you a clear reference for the part, its role on the board, and a practical approach to rail diagnosis and replacement. Use it when you need to confirm power behavior before ordering a replacement or planning hot air rework on a Snapdragon 820-class device.
PMI8994 Power IC and Its Role in MSM8996 Power Delivery
The PMI8994 power IC sits alongside the primary PMIC on MSM8996 designs and feeds several regulator outputs that the board depends on. When a secondary rail never comes up while the main PMIC looks healthy, this chip belongs on your suspect list. Understanding what it controls saves you hours of random probing and part swapping at your repair bench. The sections below cover where the chip fits in the power tree, which functional blocks you should test, and how to decide between a repair and a replacement.
Where the PMI8994 Fits in the Power Tree
The PMI8994 connects to the processor platform through the SPMI interface, which Qualcomm designs use to control power management blocks over a shared serial bus. Its place in the device tree shows it as a separate SPMI device with its own regulator, GPIO, MPP, LPG, and WLED functions. On MSM8996 boards, the regulator outputs from this chip feed LDOs that the primary PMIC relies on, so a fault here can appear as a rail that stays dead while the main PMIC shows normal activity. Your board schematic tells you exactly which rails originate from this IC and which come straight from the primary PMIC. Confirm those rail names on your specific board before you condemn the component. A clear map of the power tree turns a vague dead-board symptom into a focused test plan.
Built-In Blocks You Should Test
Beyond the regulators, the chip contains GPIO and MPP pin blocks that handle signal lines routed to peripherals on the board. It also integrates an LPG, which is a lighting pulse generator, and a WLED driver. These blocks matter when a display backlight or notification LED fails on a board that uses these functions, so a backlight complaint does not always point to the display itself. The regulator section includes supply inputs for rails named S1, S2, S3, and L1 in the Linux kernel bindings, which lets you match your schematic against those labels. Test in a fixed order: check the input supply first, then the output rail, then the enable path. This sequence tells you whether the fault sits upstream of the IC or inside it. Record each reading against the schematic value so you can compare boards from the same family later.
Bench Diagnosis and Replacement Decisions
Start with a multimeter check on each rail and compare every reading against the schematic. If the input supply is present but the output rail is missing or shorted to ground, the IC or a nearby capacitor may have failed, and a short on a downstream load can also pull the rail down. Inspect the area under a microscope for lifted pads, cracked solder joints, or burned resin before you apply any heat. Disconnect or isolate loads where your board layout allows it, so you can see whether the shorted rail clears. When you replace the IC, use a hot air station with controlled temperature and a flux suited to your process, and confirm the board revision before you order the part. Reflow the chip carefully and avoid overheating the surrounding components. Power the board from a bench supply with current limiting before you reinstall it in the housing. A new chip will fail again if a downstream load still draws excess current, so clear that fault first.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm SPMI-interfaced power management architecture
- ✓Integrated regulator outputs for MSM8996 board power rails
- ✓Built-in GPIO and MPP pin blocks
- ✓Integrated LPG (lighting pulse generator) block
- ✓Integrated WLED driver block
- ✓Reference platform support on Dragonboard 820c
- ✓Suited to board-level rail diagnosis and IC-level replacement
- ✓Pairs with the primary PMIC in MSM8996 power delivery
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PMI8994 |
| Category | Power Management IC |
| Compatibility | MSM8996 platform |
| Technology | SPMI-interfaced power management IC |
Common Repair Uses
- ✓Tracing dead secondary rails on MSM8996 boards with a multimeter
- ✓Diagnosing boards where LDO outputs fed by this IC stay low while the main PMIC looks normal
- ✓Checking backlight and LED fault paths tied to the integrated WLED and LPG blocks
- ✓Testing GPIO and MPP lines when a peripheral fails to respond
- ✓Replacing a confirmed faulty IC with hot air rework after microscope inspection
- ✓Bench-testing a replacement chip on a development board before board-level installation
Compatible Devices
- ✓Verified at chipset-family and reference-board level
- ✓MSM8996-based mobile platforms (Snapdragon 820 class)
- ✓Qualcomm Dragonboard 820c development board
- ✓Boards pairing the PMI8994 with the primary PMIC in MSM8996 power designs
- ✓Qualcomm SPMI-bus power management designs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which Snapdragon platform uses the PMI8994?
Does the PMI8994 include a backlight driver?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



