Samsung S2MPS13B2 Power IC PMIC for Exynos 5433
₨ 350
S2MPS13B2 Power IC – Main PMIC for Exynos 5433 Boards
The S2MPS13B2 power IC is Samsung’s main power management chip for Exynos 5433 motherboards. It runs 10 buck converters and 40 LDO regulators, keeps the real-time clock alive, and feeds reference clocks to the application processor, modem, and Bluetooth blocks. When this chip fails, the board loses its core supply rails and you face a dead phone with no current draw or a unit that hangs on logo. Order this replacement when your diagnosis points to the main PMIC and you need to rebuild the full power tree on an Exynos 5433 board, including the Exynos variants of the Galaxy Note 4.
S2MPS13B2 Power IC: Samsung’s Main PMIC for the Exynos 5433 Platform
The S2MPS13B2 power IC sits at the centre of every Exynos 5433 motherboard. Samsung designed the S2MPS13 as a multi-function PMIC that combines voltage regulators, an RTC block, and clock outputs in one package, and the Linux kernel’s device-tree documentation lists it alongside the S2MPS11, S2MPS14, and S2MPS15 family members. On Samsung’s own Exynos 5433 reference board, the S2MPS13 handles primary power supply duty, while a separate Maxim MAX77843 interface PMIC manages the charger, MUIC, and haptic functions. Knowing that split saves you time at the bench. A charging issue usually points to the interface PMIC, while a board that draws zero current or drops into a boot loop often points back to this main chip.
Inside the S2MPS13: 10 Buck Converters, 40 LDOs, RTC and Clock Outputs
The S2MPS13 delivers LDO1 through LDO40 and BUCK1 through BUCK10, which gives it more regulators than the S2MPS14 sibling it shares its RTC and clock design with. The buck converters carry the heavy loads: CPU clusters, GPU, and memory. The LDOs feed lower-current rails such as sensors, I/O banks, and always-on domains. On the reference board, LDO3 supplies the 1.8V rail to the ALIVE domain of the Exynos 5433, so a fault on that single output alone stops the processor from waking. The chip also produces three clock outputs labelled for the AP, the CP (modem), and Bluetooth. The processor talks to it over I2C at address 0x66, which means a damaged I2C line can mimic a dead PMIC. Check those lines before you commit to an IC change.
Diagnosing an S2MPS13B2 Power IC Fault Before You Replace It
Start with your DC power supply and watch the current when you press the power key. A board that shows zero draw, or a fixed short the moment you connect VBAT, sends you to the PMIC area first. Use your multimeter in diode mode across the large buck output capacitors around the chip and compare readings with a known-good board. A shorted capacitor wastes a good IC if you skip this step, so isolate it first. Thermal camera checks and rosin smoke tests quickly show whether the S2MPS13B2 itself heats up under injection voltage. For a hang on logo or a random restart, measure each buck output while the board tries to boot. An output that sags or never rises points to a hardware fault inside the PMIC, not a software issue that flashing will fix. Rule out the MAX77843 for any charging-only complaint.
Clean Replacement Workflow on Your Repair Bench
Mount the board in a PCB holder and shield nearby plastic connectors with heat tape. Preheat the board from below, then lift the old chip with your hot air station using quality flux and steady, even airflow. Clean the pads with solder wick at a controlled iron temperature and inspect them under your microscope for lifted or torn pads. If your replacement needs fresh solder balls, reball it with the correct stencil from your reballing kit before placement. Align the IC carefully, reflow it, and let the board cool naturally. After the IC change, confirm every buck output on the DC power supply before you reassemble the phone. This sequence protects the CPU next to the PMIC and gives you a first-time fix instead of a comeback.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Main power management IC for Samsung Exynos 5433 boards
- ✓10 buck converters for CPU, GPU, and memory rails
- ✓40 LDO regulators for low-current and always-on domains
- ✓Built-in RTC block for timekeeping
- ✓Three clock outputs feeding AP, modem, and Bluetooth
- ✓I2C control interface at address 0x66
- ✓Shares RTC and clock design with the S2MPS14 family
- ✓Restores the full power tree in one IC change
Specifications
| Brand | Samsung |
|---|---|
| Model | S2MPS13B2 |
| Category | Mobile Phone ICs > Power Management IC |
| Compatibility | Samsung Exynos 5433 platform motherboards |
| Supported Devices | Samsung Galaxy Note 4 Exynos variants (SM-N910C, SM-N910H) |
| Technology | 10 buck converters, 40 LDO regulators, RTC, AP/CP/BT clock outputs, I2C control |
Common Repair Uses
- ✓Dead phone with zero current draw on power key press
- ✓Fixed short on VBAT traced to the main PMIC
- ✓Boot loop or hang on logo caused by unstable buck rails
- ✓No power after water damage corrodes the PMIC area
- ✓PMIC heating detected during voltage injection
- ✓Missing 1.8V ALIVE-domain rail to the Exynos 5433
- ✓Replacing a PMIC damaged by a failed reflow attempt
- ✓Restoring power rails after nearby CPU-area rework
Compatible Devices
- ✓Exynos 5433 platform boards fitted with the S2MPS13 main PMIC
- ✓Samsung Exynos 5433 SoC motherboards
- ✓Samsung Galaxy Note 4 SM-N910C (Exynos)
- ✓Samsung Galaxy Note 4 SM-N910H (Exynos)
- ✓Samsung TM2 Exynos 5433 board
- ✓Samsung TM2E Exynos 5433 board
- ✓Any board whose original main PMIC reads S2MPS13B2
- ✓Exynos 5433 donor boards used for IC transplants
- ✓Not interchangeable with S2MPS14 or S2MPS15 boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is S2MPS13B2 the charging IC or the main power IC on Exynos 5433 boards?
Can I replace S2MPS13B2 with S2MPS14 or S2MPS15?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



