TQP9059 Qorvo Multimode Power Amplifier Module
₨ 400
TQP9059 Power Amplifier Module for Quad-Band GSM and Multiband LTE
The TQP9059 is a fully matched multimode multiband power amplifier module from Qorvo, covering quad-band GSM/EDGE, WCDMA and LTE bands 1, 2, 3, 4, 5, 8, 17, 20 and 26. It supports both envelope tracking (ET) and average power tracking (APT) operation, so one module fits either supply architecture. The 50 ohm matched input and output and the integrated band distribution switches reduce the external matching work on your board. Packaged as a 42-pin 5 x 7 x 1 mm module on GaAs HBT technology with CuFlip assembly, it suits technicians working on RF section faults, network issues traced to the transmit path, and board-level PA replacements.
TQP9059 Power Amplifier Module Overview for Your Repair Bench
The TQP9059 power amplifier module sits in the transmit path of a mobile phone, where it boosts the modulated signal before it reaches the antenna. Qorvo built it as a single multimode module, so one part handles GSM/EDGE, WCDMA and LTE instead of several separate PAs. When a handset shows a network issue across several bands, the PA is one of the first RF blocks you verify. Qorvo has ended production of this part, with a last-time-buy date of August 25, 2021, so confirm sourcing before you plan a board-level swap.
Multimode Coverage Across GSM, WCDMA and LTE
One TQP9059 handles quad-band GSM/EDGE alongside WCDMA and LTE, so you replace one module instead of matching several. In GMSK mode, the GSM output follows a Vramp input from the transceiver. In 8PSK mode, the same Vramp input optimizes current draw and linearity, which helps when you diagnose high current on an EDGE path. The WCDMA section runs in two modes, HPM and LPM, and the handset switches between them to extend talk time. The verified LTE band list covers bands 1, 2, 3, 4, 5, 8, 17, 20 and 26. Before you order a replacement, match the band set on your board against this list.
ET and APT Supply Compatibility
The module supports both envelope tracking (ET) and average power tracking (APT) supply schemes. Its ET optimization lets the power stage follow the signal envelope, so you should check the envelope supply rail during troubleshooting. APT compatibility means the module also operates under APT supply control, which covers a wider range of handset designs. The built-in regulator and integrated band distribution switches reduce the number of external parts the board needs around the module. In 8PSK operation, input power controls the output, so the power control loop on the board matters as much as the supply setting. Measure the supply rails and control lines first, then confirm which tracking scheme the handset uses.
42-Pin Package, Materials and Rework Notes
The TQP9059 comes in a 42-pin module measuring 5 x 7 x 1 mm, so your rework station and stencil must match that footprint exactly. Qorvo builds it on GaAs HBT technology with CuFlip assembly, which supports stable temperature behavior and ruggedness. The part carries a lead-free 260°C rating and meets RoHS and halogen-free requirements, so keep your reflow peak within that limit. Check pad alignment under a microscope before you lower the module into place with hot air. The module uses 50 ohm input and output impedance, so inspect the RF traces and any series components around the pads before you power the board back up.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Quad-band GSM/EDGE with WCDMA and LTE coverage in one module
- ✓Vramp-controlled output power in GMSK mode
- ✓Vramp-optimized bias in 8PSK for linearity and current control
- ✓WCDMA operation in HPM and LPM modes
- ✓ET-optimized and APT-compatible
- ✓Integrated band distribution switches and built-in regulator
- ✓50 ohm input and output impedance
- ✓Lead-free 260°C rating, RoHS and halogen-free
Specifications
| Brand | Qorvo |
|---|---|
| Model | TQP9059 |
| Category | Mobile Phone ICs > RF Power Amplifier Module |
| Compatibility | GSM/EDGE, WCDMA, LTE (Bands 1, 2, 3, 4, 5, 8, 17, 20, 26) |
| Supported Devices | Mobile handset RF transmit sections |
| Technology | GaAs HBT with CuFlip assembly, 50 ohm matched input and output |
| Dimensions | 5 x 7 x 1 mm, 42-pin |
Common Repair Uses
- ✓Replacing a faulty RF power amplifier after a network issue traces to the transmit section
- ✓Restoring GSM/EDGE transmit on a board with weak signal across multiple bands
- ✓Board-level PA swap on a handset with suspect high current draw during transmit
- ✓Hot air rework of a 42-pin module with microscope-checked pad alignment
- ✓Checking Vramp and supply control lines before ordering a replacement module
- ✓Diagnosing a band-specific LTE fault by confirming band coverage against the board
- ✓Comparing the PA reference on a board with the verified TQP9059 band list
- ✓Training technicians on multimode PA architecture for ET and APT designs
Compatible Devices
- ✓Verified scope is band-level RF compatibility, not device-specific.
- ✓Quad-band GSM/EDGE: GSM850, GSM900, DCS and PCS
- ✓WCDMA/UMTS Bands 1, 2, 3, 4 and 5
- ✓WCDMA/UMTS Bands 8, 17, 20 and 26
- ✓LTE Bands 1, 2, 3, 4 and 5
- ✓LTE Bands 8, 17, 20 and 26
- ✓ET-optimized and APT-compatible supply designs
- ✓Handset RF transmit sections using 50 ohm matched PA stages
- ✓Device-specific models not verified; match by band set and PA reference on the board
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the TQP9059 support ET and APT operation?
Which LTE bands does the TQP9059 cover?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



