JCID ZF005 Ultra-Sharp Pin-Type Multimeter Probe

₨ 1

JCID ZF005 Precision Probe Set

The JCID ZF005 ultra-sharp multimeter probe set puts a 0.05mm flexible pin and a 0.1mm ultra-hard pin on your bench for tight-pitch board measurements. When a standard probe slips off a crowded pad, you swap the replaceable pin and keep the same lead. A tinned copper core carries the signal, a silicone body insulates your grip, and a universal 4mm plug fits your multimeter. Mechanicpk supplies the ZF005 to Pakistani technicians who run continuity, voltage, and short-circuit checks on mobile phone motherboards every day. Two spare pin types and removable probe protectors ship in the kit.

Out of stock

15 People watching this product now!
Description

Ultra-Sharp Multimeter Probe Built for Mobile Motherboard Work

The JCID ZF005 ultra-sharp multimeter probe gives you a tip fine enough to land on one pad of a crowded phone board without touching its neighbors. JCID builds the set around replaceable pins, so a worn or bent tip costs you a pin, not a full lead. You get a flexible 0.05mm pin for delicate contact points and a 0.1mm ultra-hard pin for work that needs rigidity. That pairing covers most multimeter checks a repair bench runs on a dead phone.

Pin Design and Tip Selection

The ZF005 ships with two ultra-sharp flexible pins (0.05mm) and two ultra-hard pins (0.1mm). The flexible pin gives slightly under pressure, which keeps contact steady when your hand drifts during a long measurement. The ultra-hard pin resists bending, so it holds its line when you press through flux residue or conformal coating to reach bare copper. Gold-plated stainless steel forms the tip, which supports clean, low-resistance contact. Removable probe protectors cover the pins when the probes sit in your toolbox, which protects both the tip and your fingers.

Because the pin screws out of the body, you replace only the damaged part. Over a month of heavy use on a busy bench, that adds up to less downtime and a lower consumable cost than replacing complete leads.

Cable, Grip, and Multimeter Fit

The lead uses an 18AWG core built from 151 fine tinned copper strands. That construction keeps the cable flexible and holds low resistance across the run, and the tinned finish resists oxidation. Silicone insulation covers the cable and forms the ergonomic handle. It stays supple, and it tolerates the heat near a hot air station better than stiff PVC leads. The rated figures for the cable are 1000V and 20A, with a cable length of 101 cm, which gives you comfortable reach from your multimeter to the board holder.

A universal 4mm plug terminates each lead. If your multimeter accepts standard 4mm banana jacks, the ZF005 plugs straight in, so you keep the meter you already trust.

Where the ZF005 Fits in Your Repair Workflow

Reach for this probe during the diagnostic stage, before you commit to a hot air station or a soldering iron. Check continuity on a broken trace, measure voltage rails at the test points around the PMIC, and trace a short on a charging issue board while you hold a steady contact on a single pad. When a hardware fault points to a suspect IC, the same probe confirms the fault before you plan IC change karna. After rework, it verifies that your new joints conduct and that no bridge remains between pins. For BGA work, pair it with a microscope and a PCB holder so both hands stay free and your probe lands exactly where you aim.

Mechanicpk stocks the ZF005 alongside multimeters, microscopes, PCB holders, soldering stations, hot air stations, test boxes, and reballing kits, so you can build a complete diagnostic and rework bench from one distributor.

Additional information
Weight0.2 kg
Q & A
Please login to post questions

Key Features

  • 0.05mm ultra-sharp flexible pin for fine-pitch pads
  • 0.1mm ultra-hard pin that resists bending
  • Replaceable pins, so you keep the lead
  • Gold-plated stainless steel tips
  • Tinned copper core with 18AWG, 151-strand construction
  • Silicone cable and ergonomic grip
  • Universal 4mm plug
  • Removable probe protectors included

Specifications

BrandJCID
ModelZF005
CategoryMultimeter Probes / Precision Test Leads
CompatibilityMultimeters with universal 4mm plug inputs
Supported DevicesMobile phone motherboards, brand-independent
MaterialTinned copper core, silicone cable and handle, gold-plated stainless steel probe tips
Power Rating1000V, 20A (rated)
DimensionsCable length 101 cm; probe pin diameter 0.05mm (flexible) and 0.1mm (ultra-hard)

Common Repair Uses

  • Continuity, voltage, and short checks on mobile phone PCBs and BGA ICs.
  • Continuity testing on broken traces and jumper wires
  • Voltage rail measurement around power ICs
  • Short-circuit tracing on dead phones
  • Charging issue diagnosis at the charging port and connector pads
  • Display problem checks on flex connector pads
  • Post-rework joint verification after IC change
  • Pin-level testing on BGA ICs
  • Small wire and solder joint testing

Compatible Devices

  • Brand-independent bench tool. It fits any multimeter with a universal 4mm plug and works on mobile phone motherboards of any make.
  • Multimeters with standard 4mm banana jack inputs
  • Mobile phone motherboards from any brand
  • Samsung, Oppo, Vivo, Infinix, and Tecno boards (brand-independent contact tool)
  • iPhone logic boards
  • BGA IC test points and solder joints
  • Charging port and battery connector pads
  • Display and flex connector pads
  • Small wires and tight solder joints

FAQ

What is the product name?
The product name is JCID ZF005 Ultra-Sharp Pin-Type Multimeter Probe.
What is the brand of this product?
The brand of this product is JCID.
What is the model of this product?
The model of this product is ZF005.
What is this product used for?
This product is used for precise continuity, voltage, and short-circuit measurements on mobile phone motherboards and other fine-pitch PCBs.
Which devices are compatible with this product?
This product is compatible with multimeters that accept a universal 4mm plug, and it works on mobile phone motherboards of any brand.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which probe pin sizes come with the ZF005 multimeter probe?
The kit includes two ultra-sharp flexible pins at 0.05mm and two ultra-hard pins at 0.1mm. You replace a damaged pin without changing the cable.
What voltage and current rating does the ZF005 probe cable carry?
The cable carries a rating of 1000V and 20A, and it ends in a universal 4mm plug for standard multimeter jacks.