PM6375 001 Power ic – Qualcomm PMIC for Snapdragon 695
₨ 450
Qualcomm PM6375 001 Power ic for Snapdragon 695 Boards
The PM6375 001 Power ic is a Qualcomm power management IC that generates and sequences the core voltage rails on Snapdragon 695 5G mainboards. It ships in a 144-ball fan-out wafer-level BGA package and carries the factory marking PM6375 001. Technicians use the PM6375 001 Power IC to repair dead phones, no-power boards, boot loop and hang-on-logo faults traced to the PMIC stage on Redmi Note 11 Pro 5G, Realme 9 Pro 5G, Realme 10 Pro 5G and related models. Match the chip marking before rework, and pair it with a hot air station and reballing kit for a clean installation.
PM6375 001 Power ic: Qualcomm PMIC for Snapdragon 695 Mainboards
The PM6375 001 Power ic is the Qualcomm power management IC that feeds the core supply rails on Snapdragon 695 (SM6375) 5G mainboards. When this PMIC fails, the CPU never receives its operating voltages, and the phone presents as a dead phone with no display, no vibration and no charging response. Mechanicpk supplies the PM6375 001 Power IC for technicians who handle board-level power faults on mid-range Redmi and Realme 5G handsets. The part carries the factory marking PM6375 001 and matches the Qualcomm production code PM-6375-0-FOWNSP144, which identifies a 144-ball fan-out wafer-level package.
Where the PMIC Sits in the Power Architecture
On a Qualcomm platform, the PMIC acts as the voltage hub between the battery and charging stage and the application processor. The Qualcomm PM6375 PMIC generates the buck and LDO rails that the CPU, memory and peripheral blocks need, and it sequences those rails in a fixed order during boot. A fault anywhere in that chain stops the boot sequence. That explains why a damaged PMIC produces symptoms that look like CPU or memory failure: hang on logo, random restarts, a boot loop issue, or a board that draws current and then drops to zero.
Diagnosing a PM6375 001 Power IC Fault
Accurate diagnosis saves you from replacing a healthy chip. Connect the board to a DC power supply and watch the current draw when you press the power key. A board that shows no current, a fixed short, or a reading that climbs and then stops usually points to the power stage. Check the output capacitors around the PMIC with a multimeter in diode mode before you heat anything, because a shorted capacitor often mimics a dead PMIC. Use rosin or a thermal camera to locate the heat source on a shorted rail. Replace the PM6375 001 only after you rule out the capacitors, the battery connector line and the charging IC.
Replacement Workflow for Technicians
PMIC replacement on these boards counts as fine-pitch BGA rework, and your bench setup decides the success rate. Mount the board in a PCB holder, apply flux, and carefully remove any underfill the manufacturer applied around the chip. Preheat the board to reduce thermal stress, then lift the old chip with a hot air station at controlled airflow so you do not blow nearby small components off their pads. Clean the pads with solder wick and a soldering station, inspect them under a microscope for lifted or torn pads, and reball the new IC with a matching stencil from a reballing kit. Align the chip by its pin-1 marker, reflow, and let the board cool naturally before you power it on.
Compatible Platforms and Models
The PM6375 001 belongs to Qualcomm’s SM6375 (Snapdragon 695 5G) platform family. Pakistani repair benches see this platform mainly on Redmi Note 11 Pro 5G, Redmi Note 11E Pro, Realme 9 Pro 5G and Realme 10 Pro 5G boards, and parts suppliers also list Redmi Note 12 5G and Redmi Note 12R Pro. Always match the marking on the original chip against the replacement before you start rework, because Qualcomm uses several PM-series PMICs with similar footprints across its mid-range platforms.
Why Source the PM6375 001 Power IC from Mechanicpk
Mechanicpk stocks Qualcomm PMICs alongside the equipment a PMIC job demands: hot air stations, soldering stations, BGA reballing kits, microscopes, PCB holders, multimeters and test boxes. You source the chip and the rework tools from one distributor and keep turnaround time short. For workshops and service centers that open Snapdragon 695 boards every week, a few spare units of this Snapdragon 695 power IC on the shelf let you close dead phone and no-power jobs the same day instead of waiting on imports.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Genuine Qualcomm PMIC carrying the PM6375 001 factory marking
- ✓144-ball fan-out wafer-level BGA package for direct board-level replacement
- ✓Generates and sequences the core voltage rails for the Snapdragon 695 platform
- ✓Restores boot on dead phones when the fault sits in the PMIC stage
- ✓Fits standard PMIC rework workflows with hot air, flux and stencil reballing
- ✓Suitable for Redmi and Realme Snapdragon 695 5G board repairs
- ✓Single-unit supply for repair shops; stock depth for service centers
- ✓Pairs with Mechanicpk hot air stations, reballing kits and microscopes for a complete PMIC job
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PM6375 001 |
| Category | Power Management IC (PMIC) |
| Compatibility | Qualcomm SM6375 (Snapdragon 695 5G) platform mainboards |
| Technology | Fan-out wafer-level BGA package, 144 balls (part code PM-6375-0-FOWNSP144) |
Common Repair Uses
- ✓Board-level power-stage repair on Qualcomm Snapdragon 695 phones
- ✓Dead phone with no current draw on DC power supply
- ✓No power, no vibration, no charging response
- ✓Boot loop issue traced to the PMIC stage
- ✓Hang on logo caused by unstable core rails
- ✓Random restarts and sudden shutdowns
- ✓PMIC overheating or shorted PMIC output rail
- ✓PMIC replacement after liquid damage to the power section
- ✓BGA reballing and reflow of a cracked or lifted PMIC
Compatible Devices
- ✓Snapdragon 695 5G platform boards that use the PM6375 001 marking
- ✓Redmi Note 11 Pro 5G
- ✓Redmi Note 11E Pro
- ✓Redmi Note 12 5G
- ✓Redmi Note 12R Pro
- ✓Realme 9 Pro 5G
- ✓Realme 10 Pro 5G
- ✓Qualcomm SM6375 (Snapdragon 695 5G) mainboards
- ✓Any board with an original PM6375 001 chip marking (verify before rework)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I confirm a dead phone needs a PM6375 001 replacement and not a capacitor or CPU fault?
What equipment do I need to replace the PM6375 001 Power IC?
Related products
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



