SC6531E Original IC – Spreadtrum GSM Feature Phone CPU

₨ 450

Original SC6531E IC for Keypad Phone Board Repair

The SC6531E Original IC is a genuine Spreadtrum (UNISOC) single-chip platform for 2G keypad phones, combining the GSM/GPRS baseband, RF transceiver, Bluetooth, FM radio, embedded PSRAM, and power management unit in one 175-ball BGA package. You use it for board-level CPU replacement on Nokia, itel, and other feature phones built on the SC6531E platform. It restores handsets that show a dead phone condition, network issue, or charging issue traced to the main chip. Pair it with a matching reballing stencil, a hot air station, and an SPD-supported flash tool for a clean, reliable IC replacement on your repair bench.

17 People watching this product now!
Description

SC6531E IC: Spreadtrum Single-Chip Platform for 2G Feature Phones

The SC6531E IC sits at the center of a large share of the keypad phones that reach Pakistani repair benches every day. Spreadtrum, now trading as UNISOC, packs the GSM/GPRS baseband, the RF transceiver, Bluetooth and FM radio, embedded PSRAM, and the power management unit into one 175-ball BGA that measures 7.8 × 7.8 mm. That level of integration explains why one failed chip can stop an entire handset: when this IC fails, the phone loses power control, radio, audio, and display logic together. Its compact footprint also means a steady hand and good magnification matter as much as heat control. This SC6531E Original IC gives you a genuine replacement part for board-level work on Nokia, itel, and other 2G keypad models that run on this platform.

Inside the Spreadtrum SC6531E CPU: Architecture and Integrated Blocks

The Spreadtrum SC6531E CPU runs two embedded 32-bit microcontrollers alongside a 16-bit DSP core with dedicated accelerators. The SC6531 family uses an ARM926EJ-S application core rated up to 312 MHz on a 40 nm process, which gives budget handsets enough headroom for calls, messaging, music playback, and FM radio. The analog baseband section supplies the ADCs and DACs for the voice and baseband paths, together with PLLs, band-gap references, LDO regulators, and auxiliary drivers. The memory interface supports embedded PSRAM up to 128 Mbit, an 8-bit DDR data width, and synchronous burst access up to 104 MHz. For a technician, this architecture means the chip owns almost every subsystem you test on the board, from the power rails to the antenna path. Because the platform handles only GSM/GPRS, the SC6531E IC belongs on 2G keypad boards and never on Android smartphone boards, which helps you separate it quickly from Spreadtrum smartphone CPUs during parts sorting.

Diagnosing SC6531E IC Faults Before Replacement

Confirm the fault before you lift the chip. A dead phone with normal battery voltage but no current draw on a power key press points toward the CPU or its solder joints. A handset that stays stuck in a hang on logo condition after a verified clean flash, or one that remains dead after flash, leads in the same direction. Network issue complaints with a good antenna path and a healthy power amplifier also trace back here, because the GSM transceiver lives inside the SC6531E. Charging issue faults deserve the same attention, since the integrated PMU handles battery and supply regulation. Rule out the battery connector, the power key line, and the external flash chip on boards that use one, then measure the main LDO rails with your multimeter. Check the chip edge under a microscope for corrosion before you commit to removal. A reflow on the original chip can recover cracked joints after a drop, while liquid damage or corroded balls usually demand a full IC change.

Replacing the SC6531E IC on Your Repair Bench

Replacement follows a standard BGA rework workflow. Fix the board in a PCB holder, preheat it, then lift the old chip with a hot air station at a temperature and airflow that protect the shielding frame and nearby plastic parts. Clean the pads with flux and desoldering wick from your soldering station kit, and inspect every pad under a microscope for lifts or bridges. Reball the new SC6531E with the matching 175-ball stencil from your reballing kit, align it on the pads, and reflow it evenly. Keep the board on the holder until it cools fully, since moving it early can shift the freshly reflowed balls. After installation, flash the stock PAC firmware through Research Download, Upgrade Download, or a Spreadtrum-supported box such as Miracle Box, with Spreadtrum SCI USB drivers on your PC. A current-draw check on a DC power supply confirms a clean boot before you close the phone. When IC-level jobs become a daily routine, your natural upgrade path leads to a dedicated BGA rework station with bottom heating for repeatable results on every feature phone CPU IC you replace.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Genuine Spreadtrum (UNISOC) SC6531E single-chip platform
  • 175-ball BGA package measuring 7.8 × 7.8 mm
  • Two embedded 32-bit microcontrollers plus a 16-bit DSP core
  • Integrated GSM/GPRS baseband and RF transceiver
  • Built-in Bluetooth and FM radio blocks
  • Integrated power management unit with LDO regulators
  • Embedded PSRAM support up to 128 Mbit with 104 MHz burst access
  • Flashes with PAC firmware through Spreadtrum-supported tools

Specifications

BrandSpreadtrum (UNISOC)
ModelSC6531E
CategoryMobile Phone CPU IC
Compatibility2G GSM/GPRS feature phones built on the SC6531E platform
Supported DevicesNokia 110 (2019), itel Muzik 110, itel Signal 10, itel IT5071, itel IT5615, itel IT5618N, Logicom Le Posh 178, Logicom Le Posh 180
TechnologyGSM/GPRS baseband, integrated GSM/Bluetooth/FM RF transceivers, PMU, embedded PSRAM up to 128 Mbit
Dimensions7.8 × 7.8 mm (175-ball BGA package)

Common Repair Uses

  • Board-level CPU repair on SC6531E keypad phones
  • CPU replacement on a dead phone with normal battery voltage and no current draw
  • Network issue repair where the fault traces to the integrated GSM transceiver
  • Bluetooth or FM radio failure caused by the main chip
  • Charging issue repair linked to the integrated PMU section
  • Hang on logo faults that persist after a verified clean flash
  • Dead after flash handsets where the CPU no longer responds to the flash tool
  • Reball and reflow after drop damage cracks the BGA joints
  • Full IC change after liquid damage corrodes the chip balls

Compatible Devices

  • Verified handsets built on the SC6531E platform
  • Nokia 110 (2019)
  • itel Muzik 110
  • itel Signal 10
  • itel IT5071
  • itel IT5615
  • itel IT5618N
  • Logicom Le Posh 178
  • Logicom Le Posh 180

FAQ

What is the product name?
The product name is SC6531E Original IC.
What is the brand of this product?
The brand of this product is Spreadtrum (UNISOC).
What is the model of this product?
The model of this product is SC6531E.
What is this product used for?
This product is used for board-level CPU replacement on 2G keypad phones built on the SC6531E platform.
Which devices are compatible with this product?
This product is compatible with Nokia 110 (2019), itel Muzik 110, itel Signal 10, itel IT5071, itel IT5615, itel IT5618N, and Logicom Le Posh 178 and 180.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which flash tool works after SC6531E IC replacement?
Use Research Download, Upgrade Download, or a Spreadtrum-supported box such as Miracle Box with the stock PAC firmware and Spreadtrum SCI USB drivers installed on your PC.
What package and ball count does the SC6531E IC use?
The SC6531E uses a 175-ball BGA package measuring 7.8 × 7.8 mm, so you need a matching 175-ball stencil for reballing.