SPU13P Power IC for Samsung Galaxy A53 5G A536
₨ 900
SPU13P Power IC for Samsung A53 and A536 Board Repair
The SPU13P Power IC for Samsung A53 gives you a direct component-level replacement for the power management section of the Galaxy A53 5G (SM-A536). Supplier listings tie this PMIC to the A536 mainboard, so you can swap it on the bench instead of replacing the whole board. Use it when a dead phone, a no power-on fault, or abnormal current draw on your DC supply points to the power section. The part ships as a single surface-mount IC, ready for hot air rework. Order it from Mechanicpk for your Samsung A536 repair jobs in Pakistan.
SPU13P Power IC for Samsung A53 5G Board-Level Repair
The SPU13P Power IC for Samsung A53 serves technicians who repair Galaxy A53 5G (SM-A536) boards with power delivery faults. Supplier and distributor listings identify it as the power management IC (PMIC) for this model. You replace it at component level when a dead phone, a no power-on symptom, or abnormal current draw traces back to the power section. You get a direct replacement part for your hot air station, so you avoid swapping the whole board. This page covers fitment, the replacement workflow, and the checks that save you a second reflow.
Where the SPU13P Sits on the A536 Board
A PMIC takes the battery and charger input and distributes regulated voltages to the processor, memory, display, and the other blocks on the mainboard. When it fails or shorts, the phone shows symptoms you see daily on the repair bench: no response to a charger, no boot, a hang on logo, a boot loop issue, or heat near the IC with the battery connected. Supplier listings for the Galaxy A53 pair the SPU13P with neighbouring ICs such as the SPU14P and SM5714 for the same board. Check those parts as well before you condemn the PMIC, because a fault in one rail can mimic a failure in another. The SPU13P is the right candidate once your current-draw readings and short checks point to the power section.
SPU13P Power IC Replacement Workflow
Start with a DC power supply instead of the battery. Note the idle current, then look for a short on the main rails with a multimeter. A thermal camera or a touch of freeze spray shows you which IC heats first. Once the PMIC is your suspect, apply flux, preheat the board, and lift the IC with hot air at a controlled temperature. Protect the nearby components with Kapton tape and keep the airflow even so the neighbours do not shift. Clean the pads fully, check for lifted pads under a microscope, and place the new SPU13P with the correct orientation. Reflow, let the board cool, and test on your DC supply before you reassemble. Skipping the pad inspection is the most common reason a replacement fails on the first power-up.
Fitment and Sourcing Checks Before You Order
Confirm the board identity before you buy. Look for the Galaxy A53 5G SM-A536 marking on the mainboard and compare the IC marking on your board with SPU13P. Some marketplace listings attach this IC to other Samsung models, but the A53 and A536 pairing is the one that repeats across multiple suppliers, so Mechanicpk lists the SPU13P for that scope only. Check the package condition on arrival, and store the part in an anti-static bag until your repair slot. Keep your soldering iron, flux, solder wick, and a fine-tip tweezer ready, because the pads on a phone board leave no room for a second attempt. Pair this IC with the Hot Air Stations, Microscopes, and Reballing Kits categories at Mechanicpk to complete your rework bench.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Direct replacement part for the Samsung A53 5G (SM-A536) power section
- ✓Surface-mount IC built for hot air rework
- ✓Supports component-level repair instead of whole-board replacement
- ✓Single-piece pack for per-job use on your repair bench
- ✓Suits dead phone, no power-on, and abnormal current draw faults
- ✓Pairs with the neighbouring SPU14P and SM5714 ICs in A536 diagnostics
Specifications
| Brand | Samsung |
|---|---|
| Model | SPU13P |
| Category | Power IC (PMIC) |
| Compatibility | Samsung Galaxy A53 5G (SM-A536) |
| Supported Devices | Samsung Galaxy A53 5G (SM-A536) |
| Technology | Power management IC, surface-mount (SMD) |
Common Repair Uses
- ✓Power-section fault finding and replacement on the Samsung A536 mainboard.
- ✓Dead phone with no response to charger or battery
- ✓No power-on fault after a liquid or short-circuit event
- ✓Abnormal current draw on a DC power supply
- ✓Boot loop issue traced to the power section
- ✓Hang on logo caused by unstable supply rails
- ✓Overheating near the PMIC with the battery connected
- ✓Dead after a failed board repair or reflow attempt
- ✓Component-level PMIC change karna instead of a full board swap
Compatible Devices
- ✓Verified scope is the Samsung Galaxy A53 5G (SM-A536) mainboard; this IC is board-specific, not universal.
- ✓Samsung Galaxy A53 5G
- ✓Samsung SM-A536B
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which Samsung phone uses the SPU13P Power IC?
How do you confirm the SPU13P is faulty on a dead Samsung A53?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock



