SKY77621-31 RF PA IC – Skyworks Multimode Power Amplifier
₨ 220
SKY77621-31 Multimode PA Module
The SKY77621-31 is a hybrid multimode, multiband power amplifier module from Skyworks, built for 2.5G, 3G and 4G handset architectures. It covers the GSM850, EGSM900, DCS1800 and PCS1900 bands, plus WCDMA and LTE, with TD-SCDMA support, and it is controlled over a MIPI interface. The module combines a GSM PA block, a DCS/PCS PA block, a WCDMA/LTE block for low and high bands, and a multi-function control block in a compact 5 x 7 x 0.9 mm, 42-pad package. For technicians, it is a precise reference when isolating PA-stage faults on multimode handset boards.
SKY77621-31 RF PA IC Technical Overview
The SKY77621-31 RF PA IC is a hybrid multimode power amplifier module that handles several transmit roles in one 42-pad package. It was designed for handsets that run GSM, EDGE, WCDMA, TD-SCDMA and LTE on a shared transmit chain. Older designs split these functions across separate parts, so this module changes how you read a PA fault. A dead or weak transmit path can point to this IC, or to the control lines and network around it. Confirm the supply and control signals before you condemn the module.
Band Coverage and Radio Modes
The module carries a GSM850/EGSM900 PA block and a DCS1800/PCS1900 PA block. A separate WCDMA/LTE block covers the low and high bands. On the 2G side, it supports 2.5G Class 12 EGPRS multi-slot operation and EDGE linear modulation. On the 3G side, it handles WCDMA, HSDPA, HSUPA and HSPA+, and it lists TD-SCDMA modulation among its supported modes. On the 4G side, it supports LTE channel bandwidths of 1.4, 3, 5, 10, 15 and 20 MHz. When a handset loses signal on one band only, match the failing band to its correct PA block first. A fault confined to one band usually points to that block’s path rather than the whole module.
Control Interface and Power Control Lines
The SKY77621-31 is fully programmable through a Mobile Industry Processor Interface (MIPI). Its multi-function control block sits on a CMOS IC that provides the internal MIPI interface and operation. Power control depends on the mode. In GMSK mode, the VRAMP input sets output power. In EDGE mode, the PIN input controls output power, and VRAMP sets the bias. The module also offers MIPI-programmable bias modes that trade efficiency against linearity for 3G and 4G. Its extremely low leakage current helps standby time, so an abnormal idle current on the board is worth checking. Verify the MIPI, VRAMP and PIN lines with your meter or scope before you replace the IC, because a control-line fault can mimic a dead PA.
Package, Matching and Bench Handling
The module measures 5 x 7 x 0.9 mm and uses a 42-pad multi-chip module (MCM) surface-mount package. Its InGaP die and silicon die sit on a multi-layer laminate substrate with passive components. The RF input and output ports are internally matched to 50 ohms, so the board does not need extra matching work at those ports during a swap. The compact, pad-dense footprint calls for controlled heat during removal and placement. A hot air station, a reballing kit for pad cleanup, and a microscope for pad inspection suit this work. Inspect every joint before you power the board.
Repair Workflow Fit
On a multimode handset, this module sits in the transmit section, between the baseband transmit output and the antenna path. Start diagnosis with the power rails and control signals, then measure RF output on each band you suspect. Use a multimeter to check the supply and control lines first. A soldering station and a PCB holder keep the board steady during any module work. Keep the software side separate. Firmware and flashing faults belong to ISP pinout tools, eMMC programmers or UFS adapters, not to the PA stage. Splitting hardware and software checks keeps your repair time predictable and your bench workflow clean.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Hybrid multimode, multiband PA architecture
- ✓Separate GSM850/EGSM900 and DCS1800/PCS1900 PA blocks
- ✓WCDMA/LTE block covering low and high bands
- ✓Fully programmable through MIPI control
- ✓MIPI-programmable bias modes for 3G and 4G efficiency and linearity
- ✓Analog VRAMP control for 2G/2.5G GMSK power and EDGE bias
- ✓RF ports internally matched to 50 Ω
- ✓Compact 5 x 7 x 0.9 mm, 42-pad MCM package
Specifications
| Brand | Skyworks |
|---|---|
| Model | SKY77621-31 |
| Category | RF Power Amplifier Module (PAM) |
| Compatibility | GSM850/EGSM900, DCS1800/PCS1900, WCDMA, LTE, TD-SCDMA |
| Supported Devices | 2.5G/3G/4G multimode handset transmit paths |
| Technology | Hybrid MMMB, MIPI-controlled, InGaP die with silicon die, RF ports internally matched to 50 Ω |
| Dimensions | 5 x 7 x 0.9 mm, 42-pad MCM, surface mount |
Common Repair Uses
- ✓Functional repair scenarios tied to this module’s role in the transmit path.
- ✓Isolating PA-stage faults where weak output or lost registration affects one band
- ✓Checking VRAMP and PIN power control lines during bench diagnostics
- ✓Verifying MIPI control communication before replacing the module
- ✓Board-level PA replacement with hot air and microscope inspection
Compatible Devices
- ✓Verified scope only, at multimode 2.5G/3G/4G handset architecture level. Device-level compatibility is not listed.
- ✓Multimode handsets with GSM/EDGE (GSM850, EGSM900, DCS1800, PCS1900) transmit paths
- ✓WCDMA and HSPA+ (bands I, II, III, IV, V, VIII, IX) transmit paths
- ✓LTE transmit paths with 1.4 to 20 MHz channel bandwidths
- ✓TD-SCDMA transmit paths
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this module support LTE?
How is this module controlled?
Related products
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



