BQ25890H Charger IC 5A I2C Battery Management IC
₨ 250
5 A I2C Single-Cell Li-Ion Charger IC
The BQ25890H is a 5 A single-cell charger IC from Texas Instruments with NVDC power path management and I2C control. It accepts a 3.9 V to 14 V input and charges Li-Ion and Li-Polymer cells up to 4.6 V. Battery voltages down to 2.5 V are supported, and an 11 mΩ discharge MOSFET with IRCOMP compensation keeps the charging path efficient at the cell. Use this part when you need a fast, register-controlled charge path on a smartphone, tablet, or portable device board. It suits technicians who are replacing a faulty charging IC and want the same electrical performance as the original design.
The BQ25890H charger IC is a 5 A switch-mode battery charge management and power path IC built for single-cell Li-Ion and Li-Polymer batteries in smartphones, tablets, and other portable devices. Its NVDC power path lets the system run from the input source while the battery charges, and it can bring a deeply discharged or missing battery up without stalling. On a repair bench, this single part sits at the center of the charging circuit, so a fault here often appears as a charging issue on a board that still shows normal logic-side supply. Understanding its position in the power tree lets you check the input, the battery connector, and the output rail in the right order before you lift any component. The device accepts an operating input range from 3.9 V to 14 V, with an absolute maximum input rating of 22 V. That rating matters when you test a board on a bench supply or when an adapter outputs more than its rated voltage during a fault. The battery charge voltage range runs from 3.84 V to 4.6 V, which covers standard Li-Ion chemistries. Charge current reaches up to 5 A, so the part targets high-current fast charging paths rather than low-power designs. Each of these values gives you a clear reference point when you compare a donor board against a replacement part. On the battery side, the IC supports battery voltages down to 2.5 V, which helps with deeply discharged cells that would otherwise prevent a charger from starting. Its integrated 11 mΩ battery discharge MOSFET supports discharge currents up to 9 A, and IRCOMP compensates for the resistance between the charger output and the cell terminal. The part also senses battery temperature during both charge and boost operation. Low battery leakage of about 12 µA supports ship mode, which matters when a device sits unused for long periods. The control interface is I2C, and the device also supports flexible autonomous operation. Its 7-bit slave address is 6Ah (1101010 binary), so you can read and write its registers with a suitable I2C tool when the board exposes the bus. Input current limit and charge current are both set through registers, and an integrated ADC lets you check live system readings during diagnosis instead of relying only on a multimeter. USB detection and USB on-the-go boost mode are supported, which covers reverse power scenarios on compatible designs. The package is a 24-pin WQFN measuring 4 mm by 4 mm with 0.5 mm pitch and a maximum height of 0.8 mm. The exposed power pad under the package must solder to the PCB ground, and the datasheet calls for sufficient thermal vias directly beneath the IC, connected to the ground plane on the other layers. Keep the output capacitor close to the inductor and the IC, and place decoupling capacitors next to the IC pins with short traces. These layout details determine whether the part runs cool and stable, so a rework that skips them often returns as overheating or a repeated fault. During replacement, use a hot-air station at a controlled temperature, apply fresh flux, and inspect the pad solder before you power the board. After the swap, power the board from a current-limited supply, confirm the charge path with an I2C register read, and verify battery voltage and charge status before you return the device to the customer.
| Weight | 0.1 kg |
|---|
Key Features
- ✓5 A maximum charge current for fast charging on single-cell Li-Ion and Li-Polymer batteries
- ✓NVDC power path lets the system run while the battery charges
- ✓Input operating range of 3.9 V to 14 V, with a 22 V absolute maximum rating
- ✓Battery voltage support down to 2.5 V for deeply discharged cells
- ✓11 mΩ battery discharge MOSFET with discharge current up to 9 A
- ✓IRCOMP compensation between the charger output and the cell terminal
- ✓I2C control with autonomous operation for flexible charge settings
- ✓USB detection and USB on-the-go boost mode support
Specifications
| Brand Entity | Texas Instruments |
|---|---|
| Product Entity | BQ25890H 5 A single-cell battery charger IC |
| Technology Entity | NVDC power path management, I2C-controlled switch-mode buck charger, IRCOMP |
| Compatible Device Entities | Single-cell Li-Ion and Li-Polymer charging circuits in smartphones, tablets, and portable devices |
| Repair Process Entity | Charging IC replacement and charging circuit diagnosis |
| Industry Entity | Mobile phone repair and PCB board-level repair |
Common Repair Uses
- ✓Replacing a faulty charging IC on a phone or tablet board
- ✓Diagnosing a charging issue where input power is present but the battery does not charge
- ✓Restoring charge on a board with a deeply discharged battery
- ✓Reading I2C register settings during charge-path diagnosis
- ✓Rework of the charging stage after a short or overheating fault
- ✓Board-level power path repair on devices that run from input while charging
Compatible Devices
- ✓Single-cell Li-Ion battery charging circuits
- ✓Single-cell Li-Polymer battery charging circuits
- ✓Smartphone and tablet power boards (general scope, not model-specific)
- ✓Portable device charging paths with USB input
FAQ
What is the product name?
What is the brand of this product?
What is this product used for?
Who should use this product?
What is the input voltage range of the BQ25890H?
What is the I2C address of the BQ25890H?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



