Arduino USB Host Shield MAX3421E for Uno and Mega
₨ 1
Arduino USB Host Shield for Uno and Mega Projects
The Arduino USB Host Shield adds full USB host capability to your Arduino board using the MAX3421E controller. Your Uno or Mega becomes the host that reads keyboards, mice, game controllers, and USB serial adapters. It plugs onto the board and communicates over SPI through the ICSP header, so the shield connects without custom wiring. Pair it with the USB Host Shield 2.0 library by felis and you can read HID input from a sketch. Power comes from the Arduino, with up to 500 mA available when the board runs from its barrel jack. Use it when your project needs USB peripherals instead of a PC.
Out of stock
Arduino USB Host Shield for USB Peripheral Control
The Arduino USB Host Shield turns a standard Uno or Mega into a USB host. Built around the MAX3421E controller, it lets your sketch detect and read USB keyboards, mice, game controllers, serial adapters, and flash drives. Most Arduino boards cannot act as a USB host on their own, so this shield fills that gap. Your repair bench benefits when you build a test rig that reads input from USB peripherals or logs data from a serial adapter. The sections below cover how the controller works, which device classes run on it, and how to power your build safely.
How the MAX3421E Controller Works
The MAX3421E is a USB 2.0 peripheral and host controller that Maxim developed, and the part now belongs to Analog Devices. In host mode it supports full-speed operation at 12 Mbps and low-speed operation at 1.5 Mbps. The shield does not rely on a USB port built into the Arduino. Instead, your board talks to the controller over SPI through the ICSP header, and the shield exposes a Type-A host port for your peripheral. The Type-A port accepts standard USB-A plugs, so you can use the cables and adapters you already keep on your bench. Because the controller handles the USB protocol layer, your code works with device reports and data packets rather than raw signal timing. This split keeps the sketch simple even when a device behaves in unexpected ways.
Supported Peripherals and Device Classes
The USB Host Shield 2.0 library handles several device classes through a single shield. HID devices such as keyboards, mice, and joysticks run from the library’s example sketches. USB-to-serial converters based on FTDI, PL-2303, and CDC chipsets are also supported, which helps when you need a PC-style serial link on the bench. Mass storage covers USB sticks and memory card readers, with FAT32 file access listed for the Mega board. Bluetooth dongles and Android devices in accessory mode fall within the library scope as well. Each class is handled by its own driver inside the library, so you include only the classes your project needs. This keeps memory use lower on an 8-bit board with limited RAM. Test each peripheral before you commit to a design, because support depends on the device class and firmware of the attached hardware.
Power, Board Compatibility, and First Run
The shield draws its power from the Arduino. When the board runs from its barrel jack, the shield can supply up to 500 mA to the USB device. When the board runs from USB power, the limit drops to 400 mA. Plan your peripheral load around those figures, because a power-hungry device can reset the board or stall the sketch. When you size a power supply, use a regulated 5 V source on the barrel jack rather than relying on a computer USB port. That choice gives the shield headroom for keyboards and storage drives at the same time. The Arduino Uno and Mega 2560 are the documented compatible boards, and some vendors also list the Mega 1280. To start, mount the shield on the board, install the USB Host Shield Library 2.0 from the Arduino Library Manager, and open the keyboard or mouse example. A detected device prints its details to the Serial Monitor, which confirms the link before you write custom code.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Full USB 2.0 host support using the MAX3421E controller
- ✓Full-speed (12 Mbps) and low-speed (1.5 Mbps) host operation
- ✓SPI communication through the ICSP header
- ✓Type-A USB host port for standard USB peripherals
- ✓Arduino shield form factor for Uno and Mega boards
- ✓Supports HID, USB serial, mass storage, and Bluetooth dongle classes
- ✓Hub support through the USB Host Shield 2.0 library
- ✓Powered from the Arduino board with up to 500 mA for peripherals
Specifications
| Brand | Arduino |
|---|---|
| Category | Arduino Shields |
| Compatibility | Arduino Uno, Arduino Mega 2560 |
| Supported Devices | HID keyboards, mice, and joysticks; FTDI, PL-2303, and CDC USB serial adapters; USB mass storage; Bluetooth USB dongles |
| Technology | MAX3421E USB 2.0 host controller, full-speed (12 Mbps) and low-speed (1.5 Mbps) host operation, SPI interface |
| Input Voltage | 5 V (from Arduino board) |
| Power Rating | Up to 500 mA (barrel jack power), up to 400 mA (USB power) |
Common Repair Uses
- ✓Test rigs and bench tools that read or log data from USB peripherals
- ✓Building a USB keyboard or barcode input station for a diagnostic rig
- ✓Reading data from a USB serial adapter connected to a device under test
- ✓Driving a mouse-controlled test jig for repetitive input testing
- ✓Logging test results to a USB flash drive from an Arduino-based tool
- ✓Prototyping a USB game controller interface for a custom test panel
- ✓Connecting Android devices in accessory mode for lab test automation
- ✓Testing multiple USB peripherals through a USB hub on one board
- ✓Reading firmware or configuration files from USB storage in a custom tool
Compatible Devices
- ✓Arduino Uno and Mega boards, with USB device classes supported through the MAX3421E host controller
- ✓Arduino Uno (ATmega328P boards)
- ✓Arduino Mega 2560
- ✓Arduino Mega 1280
- ✓USB keyboards (HID)
- ✓USB mice and joysticks (HID)
- ✓FTDI, PL-2303, and CDC USB serial adapters
- ✓USB flash drives and memory card readers (FAT32 on Mega)
- ✓Bluetooth USB dongles
FAQ
FAQ: What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which USB device classes does the shield support?
Does the USB Host Shield work with USB hubs?
What is the maximum current available to a USB device?
Related products
Flash 64 Ultra Tool Box full set – UFS eMMC ISP Programmer
In stock



