Mechanic VS 900M-T-IS Soldering Iron Tip for Mobile Repair
₨ 400
900M-T-IS Soldering Iron Tip for Fine-Point Repair Work
The Mechanic VS 900M-T-IS is a replacement soldering iron tip built for 900M-series handles and stations. Its copper core with iron plating moves heat from the base toward a fine point, which helps when you need to tin a small pad or lay a jumper wire on a crowded board. You can restore a worn point without buying a new iron. It suits phone repair benches, PCB rework, and fine component leads. Confirm your handle uses the 900M sleeve before ordering.
Out of stock
900M-T-IS Soldering Iron Tip for Jumper and Fine-Lead Work
Your repair bench depends on how cleanly heat reaches the joint, and the 900M-T-IS soldering iron tip is designed to deliver that heat to a fine working point. It belongs to the 900M tip family, so it fits the handles and stations that accept this sleeve style. When your current tip stops tinning, loses its point, or lacks the reach for small pads, a matched replacement restores the bench without changing the whole iron. This page covers the core construction, fitting notes, and the workflow where this tip earns its place.
Copper Core and Plated Finish
Copper carries heat well, and that property matters at the tip. The core is copper, which draws heat from the heater element and moves it quickly to the point, so the joint reaches solder melting temperature without a long wait. An iron plating covers the copper to resist oxidation and the everyday wear of cleaning and tinning. Wipe the tip on a damp sponge or brass wool between joints to keep it tinned. The plating helps the point hold its shape over many cycles. Filing or scraping the working surface removes the plating quickly, so avoid abrasive cleaning on the point.
Fitting the 900M-Series Handle
Fit comes first, because a tip that rocks in the sleeve transfers heat unevenly. The 900M-T-IS is made for the 900M-series handles and the 900M-T series station family. Many technicians also fit this tip family to 936-series stations, since the same sleeve style appears on several 900M-type handles. Before ordering, remove your current tip while the iron is cool, compare the sleeve shape against your handle, and seat the new tip fully before powering up. A loose fit leaves a gap at the heater, so the tip runs cooler than the display suggests. If the sleeve differs from your handle, check the model before buying. Matching the family prevents wasted cost.
Jumper Wire and Fine-Lead Soldering
This tip earns its place in jumper and fine-lead tasks. On a mobile board, tin the point, bridge a jumper wire between two pads, and hold the iron just long enough for the solder to flow without lifting the pad. For component legs, the fine point lets you reach a single lead without touching neighboring pins. Keep the tip at a moderate working temperature and use a light touch. Add a small amount of flux before the joint so the solder wets the pad quickly. That shortens the time the tip sits on the trace. A clean, tinned point is faster and more controlled than a dirty one.
Knowing When to Replace the Point
A tip shows its age before it fails. A darkened point, uneven tinning, or pitted plating means the tip no longer transfers heat evenly. If solder refuses to wet the point even after cleaning, the surface has degraded and the joint quality will drop. Replacing the tip at that stage costs far less than repairing a damaged trace caused by poor heat transfer. Keep one spare 900M-T-IS on the bench so a worn point never stops a repair. Rotate between your spare and your main tip to spread wear and keep your workflow moving.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Copper core for fast heat transfer to the point
- ✓Iron plating to resist oxidation and everyday wear
- ✓Fine pointed geometry for precise joints
- ✓Fits 900M-series irons and 900M-T series stations
- ✓Replaces a worn tip without replacing the whole iron
- ✓Suited to jumper wire and fine-lead soldering
- ✓Supports a tin-and-clean workflow over many cycles
Specifications
| Brand | Mechanic |
|---|---|
| Model | 900M-T-IS |
| Category | Soldering Iron Tips |
| Compatibility | 900M-series soldering irons and 900M-T series stations |
| Material | Copper core with iron plating |
Common Repair Uses
- ✓Jumper wire soldering on mobile phone boards
- ✓Soldering fine component leads on PCBs
- ✓Small SMD pad rework with controlled heat
- ✓Fine-pitch trace repair with light solder
- ✓Tinning and re-tinning the working point
- ✓Soldering connector pins on charging boards
- ✓Small IC pad cleanup with a fine point
- ✓Assembly work with fine leads on hobby electronics
Compatible Devices
- ✓Scoped to the 900M tip family (handle and station type), not a specific phone model
- ✓900M-series soldering irons with a matching sleeve
- ✓900M-T series soldering stations
- ✓936-series stations fitted with 900M-type handles
- ✓927, 928, 933, and 937 stations that use 900M-type handles
- ✓Mobile phone repair benches using 900M-type handles
- ✓PCB rework stations using 900M-type handles
- ✓Hobby electronics setups using 900M-type handles
- ✓Universal within the 900M family, not device-specific. Confirm the sleeve before ordering.
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which handles accept the 900M-T-IS tip?
How do I know when to replace the tip?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



