Mechanic 900M-T-K Knife Lead-Free Soldering Iron Tip

₨ 1

900M-T-K Knife Soldering Tip for Lead-Free Board Repair

The 900M-T-K knife soldering tip is a lead-free replacement for 900M-series handpieces on Hakko-compatible stations, including 936, 937, and 938 models. Its 5mm knife edge gives you a broad working face for dragging solder, tinning flat pads, and clearing bridges on connector rows. A red copper base with plated coating carries heat into the joint and recovers quickly after contact. Use it for motherboard repair, charging-port reflow, and pad cleanup before IC work. Keep one in your kit for the flat-edge jobs that finer bevel tips cannot handle comfortably.

Out of stock

10 People watching this product now!
Description

900M-T-K Knife Soldering Tip for Board-Level Repair

The 900M-T-K knife soldering tip is a flat, chisel-style replacement built for 900M-series handpieces. If you need a dependable 900M-T-K knife soldering tip for lead-free work, this tip gives you a wide, flat edge that carries heat into large pads and broad joints. Your repair bench gets a consistent contact surface for dragging solder, cleaning pads, and lifting adhesive residue from motherboards. The blade measures about 5mm across, which sits between fine bevel tips and heavy chisels. It suits technicians who handle board-level work daily and want one tip that covers several common jobs without frequent swaps.

Where This Tip Fits in Your Repair Workflow

Most board-level jobs follow a predictable sequence: inspection, component removal, pad preparation, and rejoining. This knife tip works mainly in the removal and preparation stages. After you lift a faulty connector or a damaged chip, the pads often carry old solder and flux residue. Use the flat edge to tin and clean those pads before the new part goes down. Your workflow stays faster because you do not switch to a finer tip for every pad. Pair this tip with a clean sponge and fresh flux for repeatable results on motherboard repairs. It also reflows solder on charging-port pins and other flat connector rows.

Heat Transfer and Tip Geometry

The tip uses a red copper base with multilayer alloy plating and a nickel-plated outer layer. This construction gives the iron good thermal conductivity, so the tip recovers heat quickly after contact with a large solder joint. The listing for this series cites rapid heating, with heat conduction time shortened to roughly 0.5 seconds. Your joints stay consistent because the tip holds temperature under load. The stainless steel housing limits heat loss along the shank, which means steadier output at the work surface. The straight and curved cutter head design makes it easier to reach awkward angles around shield cans and connector housings. Keep your station temperature below the tip’s rated ceiling of about 480°C, and let the tip transfer heat rather than pressing hard on the pad.

Using the Knife Edge for Pads, Joints, and Glue Removal

The knife profile lets you drag solder in one direction across flat pins. Hold the flat face at a shallow angle, feed fresh solder, and pull the bridge away from the pad. This technique works well for bridged flat IC legs and connector rows. For glue or underfill residue, warm the area first so the edge can lift the softened material. Avoid scraping hard on copper traces, since aggressive contact can lift pads. Your technique matters more than the tip itself. Tin the face after every few joints to keep wetting consistent. Wipe the tip on a damp sponge between passes, then retin before you start the next area. These habits keep each joint clean on your repair bench.

Care, Storage, and Tip Life

Tip life depends mostly on how you treat the working surface. Wipe the iron on a damp sponge at the start of each session and after heavy use, because oxidation builds up fast on copper-based tips. Keep the stand clean and dry, and avoid leaving the handpiece at full heat through long idle periods. Use lead-free solder with an appropriate flux rather than forcing the tip to clean dirty joints. When the plating wears and the face stops wetting, replace the tip instead of pushing extra temperature through it. Store spare tips in a dry tray so you can swap quickly during a busy repair day.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 5mm knife blade for broad contact on flat pads and joints
  • Lead-free solder compatible
  • Red copper base with multilayer alloy plating
  • Nickel-plated outer layer for rust and corrosion resistance
  • Stainless steel housing that limits heat loss
  • Rapid heat recovery, with heat conduction time cited at about 0.5 seconds
  • Straight and curved cutter head design for awkward angles
  • Easy to tin and clean with a damp sponge

Specifications

BrandMechanic
Model900M-T-K
CategorySoldering Tips
Compatibility900M-series Hakko-compatible handpieces and stations
Supported Devices936, 937, 938, 969, 8586, 852D soldering stations
TechnologyLead-free soldering iron tip
MaterialRed copper base with multilayer alloy plating
Tip ShapeKnife
Blade Width5 mm
Tip Length42 mm
Temperature Range200–480°C

Common Repair Uses

  • Dragging solder to remove bridges on flat IC legs and connector pins
  • Tinning and cleaning pads before replacing a component
  • Reflowing solder joints on charging-port and flat connector pins
  • Removing glue or adhesive residue from motherboard areas after gentle heating
  • Desoldering and lifting components from large pads with the flat edge
  • Cleaning solder and flux residue from board pads before IC work
  • Reflowing solder on large ground pads and thick terminals
  • Light pad rework on motherboards during board-level repair

Compatible Devices

  • 900M-series handpieces and stations; compatibility scope based on verified listings, not device-specific
  • Hakko 936 soldering station (900M-series handpiece)
  • Hakko 937 soldering station (900M-series handpiece)
  • Hakko 938 soldering station (900M-series handpiece)
  • 969, 8586, and 852D soldering stations
  • Hakko 900M-series handpieces with M926 or 900M base
  • Hakko 907ESD handpiece (900M series)
  • Hakko 907, 908, and 942 handles (listed as applicable)
  • Lead-free solder workflows on flat pads and connector rows

FAQ

What is the product name?
The product name is Mechanic 900M-T-K Knife Lead-Free Soldering Iron Tip.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is 900M-T-K.
What is this product used for?
This product is used for lead-free soldering, pad tinning, solder bridge removal, and flat-pin reflow on board-level repairs.
Which devices are compatible with this product?
This product is compatible with 900M-series handpieces and stations, including Hakko 936, 937, and 938 models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can the 900M-T-K tip be used with lead-free solder?
Yes, the tip is listed as a lead-free soldering iron tip and works with lead-free solder on flat pads and joints.
Does the 900M-T-K fit the 900M handpiece with an M926 base?
The 900M-T-K is listed for 900M-series handpieces with M926 or 900M bases, so confirm your handpiece base before purchase.