Mechanic VS 900M-T-SK Small Knife Soldering Iron Tip

₨ 400

900M-T-SK Small Knife Tip for Drag Soldering and Fine-Pitch Repair

The 900M-T-SK soldering tip is a small knife profile from the Mechanic VS series, built for drag soldering multi-pin ICs and correcting bridges on narrow pitches. Its compact face reaches tight spots where a wider K tip would touch neighbouring components. It follows the 900M-T universal fit, so it works with the 900M-compatible stations already on your bench. The tip measures 40.8mm in total length with a 4mm inner bore and 6.5mm shank, and it suits lead-free soldering work.

In stock

11 People watching this product now!
Description

900M-T-SK Small Knife Soldering Tip for Drag Soldering and Fine-Pitch Work

The 900M-T-SK soldering tip is the small knife member of the 900M-T family, and the Mechanic VS series carries it alongside the I, IS, and K shapes. It gives you a contact face narrow enough to work between closely spaced pads while keeping enough thermal mass to wet a pin row in a single pass. On a crowded board, this geometry lets you reach the tight spots around CPU legs, connectors, and power sections without touching components you want to keep. Think of it as the tip you reach for when the standard K profile is too wide for the joint in front of you.

Where the Small Knife Shape Fits Your Workflow

Drag soldering a multi-pin IC is the core task for this tip. You load the working face with solder, apply flux along the leg row, and pull the molten solder across each pin in a controlled pass. Keep the flat of the face in contact with the pad, not only the edge, so heat transfers evenly across the joint. The SK profile keeps the contact area small enough to clear neighbouring passives, so you avoid lifting parts you never meant to touch. The same technique corrects bridges left behind by a previous rework attempt. Remove the excess solder with the tip, then reflow the joint until each pad shows a clean, even fillet. Work at a steady speed, lift the tip cleanly at the end of each row, and check every pin under a microscope before you move on. A bridge that looks clean from above can still hide a short beneath a leg. Pair this tip with a microscope from our catalog and keep flux and solder wick close at hand for quick cleanup.

Specifications at the bench: The listed dimensions are a 4mm inner bore, a 6.5mm shank, and a total length of 40.8mm, with a net weight of 61g. These measurements matter when you check fit in a handle, because a loose shank reduces heat transfer and gives uneven wetting. Confirm the tip seats fully before you power the station.

Station Compatibility and Setup

The 900M-T series is designed as a universal fit for 900M-compatible soldering stations. Mechanic’s master series listings name the Hakko 936, 937, 938, 942, 907, and 908 platforms among the supported models. Set your station to a temperature that suits your solder alloy, since lead-free wire typically needs more heat than leaded wire. Tin the working face before each joint, and keep a damp sponge or brass wool on the bench. Before you blame the tip for poor performance, check the iron handle and heater element. A worn heater or loose connection can mimic a tip fault, so test the station with a fresh tip before you decide. Store spare tips in a dry box so the plating stays clean between jobs.

Care and Maintenance for Longer Tip Life

The plated working face protects the tip body, so keep it intact. Never file or scrape the face with abrasive paper, because removing the plating shortens service life. Clean oxidation with a sponge and retin the face after each cleaning. Avoid leaving the iron hot and dry for long periods, and let the tip cool before you handle it. Keep a short log of tip changes on each station so you can track service life across jobs. That record helps you spot a station that heats unevenly before it damages a board. A tip kept tinned and clean delivers consistent heat across each drag pass, which keeps your results predictable from one board to the next.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Small knife profile for tight-clearance drag soldering
  • 900M-T series universal fit
  • Lead-free compatible design
  • Designed for narrow-pitch and bridge correction work
  • Compact 40.8mm total length
  • 4mm inner bore and 6.5mm shank

Specifications

BrandMechanic
Model900M-T-SK
CategorySoldering Iron Tip
Compatibility900M-T series soldering stations
TechnologyLead-free compatible soldering tip
Dimensions40.8mm total length, 4mm inner bore, 6.5mm shank

Common Repair Uses

  • Drag soldering multi-pin ICs on motherboards
  • Correcting solder bridges on narrow pitches
  • Soldering fine-pitch connectors in tight board areas
  • Lead-free soldering work at lower temperatures

Compatible Devices

  • 900M-T series stations, scoped to the verified listings below
  • Hakko 936, 937, 938, 942, 907, and 908 soldering stations (named in Mechanic’s master series listings)
  • Hakko 888D soldering stations (900M-T series listings)
  • Yihua 878 and 852 soldering stations (900M-T series listings)
  • Atten soldering stations (900M-T series listings)
  • Other 900M-compatible soldering stations and irons

FAQ

What is the product name?
The product name is Mechanic VS 900M-T-SK Soldering Iron Tip.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is 900M-T-SK.
What is this product used for?
This product is used for drag soldering multi-pin ICs, correcting solder bridges, and soldering on narrow pitches.
Which devices are compatible with this product?
This product is compatible with 900M-T series soldering stations, including the Hakko 936, 937, 938, 942, 907, and 908 platforms named in Mechanic’s listings.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the 900M-T-SK tip suitable for lead-free soldering?
Yes, the 900M-T-SK is listed as lead-free compatible and suits lower-temperature lead-free soldering work.
What is the difference between the SK and K tip?
The SK is a small knife shape that reaches tighter spots where a wider K tip may touch surrounding components.