Mechanic 530 Electronic Contact Cleaner 550ML Pakistan
₨ 700
Contact Cleaner Spray for Mobile Repair Benches
The Mechanic 530 is a 550ml electronic contact cleaner spray for removing dust, grease, oil, and flux residue from PCBs, connectors, and switches. It dries quickly and is described as non-conductive, so you can clean a board without leaving a film that interferes with contacts. The precision nozzle helps you direct the spray into tight areas around charging ports and board-level components. It suits cleaning work before reballing or after soldering on mobile and laptop boards.
Out of stock
Mechanic 530 Contact Cleaner Spray for Mobile Repair Benches
A contact cleaner spray for mobile repair is only useful when it removes contamination without leaving anything behind on the board. The Mechanic 530 550ml is sold for precision electronics, where dirty contacts and leftover flux cause charging faults, network problems, and intermittent display issues. Sellers describe it as a fast-drying, non-conductive cleaner for printed circuit boards, connectors, and switches, so it fits a routine cleaning step on most repair benches.
Where This Cleaner Fits in Your Repair Workflow
Most board work involves a cleaning step at two points. The first is before a chipset is reballed or a component is replaced, when oil, grease, and old solder residue sit under the part and stop the new solder from wetting properly. The second is after soldering, when flux remains around the joints. Spraying the area, letting it evaporate, and then inspecting under a microscope tells you whether the board is ready for the next stage. One listing for this formula specifically mentions its suitability for reballing, which makes it a practical choice for this step.
Fast Drying and Non-Conductive Formula
Drying speed matters on a busy bench. The formula is described as evaporating quickly and leaving no residue, so you can move to power testing without waiting for a sticky film to clear. Because it is described as non-conductive, a small overspray near live contacts carries less risk than a water-based or conductive cleaner. Even so, treat the spray as a supplement to careful technique. Keep the board dry and clean before you reconnect anything, and do not assume a non-conductive label means the board is safe while powered.
Precision Nozzle for Tight Connectors
Charging ports, SIM trays, and board-to-board connectors leave little room for a wide spray pattern. The precision nozzle lets you deliver a thin stream into these gaps, which keeps the cleaner where you need it. Work in short bursts, direct the flow from the side of the connector, and use a soft brush afterwards to loosen stubborn debris. Ending each pass with a dry-air blow helps the cleaner evaporate fully before inspection.
Using It Safely on Your Repair Bench
Work in a ventilated area and avoid breathing the spray. Keep it away from eyes and skin, and store the can upright in a cool place. Always disconnect power from a device before cleaning it. Wait until the surface is completely dry before reconnecting power or running a test. These habits protect you and the board, and they fit naturally with the rest of a well-organized repair bench that includes a PCB holder, a microscope, and a multimeter.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Fast-drying formula that evaporates quickly
- ✓Described as non-conductive for electronic boards
- ✓Leaves no residue on cleaned surfaces
- ✓Precision nozzle for tight connector areas
- ✓550ml bottle for repeated bench use
- ✓Removes dust, grease, oil, and flux residue
Specifications
| Brand | Mechanic |
|---|---|
| Model | 530 |
| Category | Electronic Contact Cleaner |
| Compatibility | Universal, not device-specific |
| Technology | Fast-evaporating, non-conductive cleaning solvent |
Common Repair Uses
- ✓Removing oil, grease, and dust from PCBs before a chipset reball
- ✓Cleaning flux residue after soldering or rework
- ✓Clearing dirty charging port contacts during charging-issue repairs
- ✓Cleaning switch and keypad contacts on mobile boards
- ✓Preparing board areas before IC change or jumper work
- ✓Cleaning connector pins before reconnecting a display or board
- ✓Removing residue from a board after a liquid damage cleaning step
- ✓General contact maintenance on repair benches
Compatible Devices
- ✓Universal, not device-specific. Verified use covers general electronics and mobile board work.
- ✓PCB and motherboard contacts
- ✓Charging ports and board connectors
- ✓Switches and keypad contacts
- ✓Sockets and relays on repair boards
- ✓SIM and memory card trays
- ✓Laptop motherboard areas
- ✓Power button and volume switch contacts
- ✓Other precision electronic assemblies
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use this cleaner on a device that is still powered?
Is this cleaner suitable before reballing a chipset?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



