RELIFE RL-420-UV Flux Paste 10cc for BGA Reballing
₨ 1
RELIFE RL-420-UV Flux Paste 10cc for Phone Mainboard BGA Work
The RELIFE RL-420-UV is a light yellow flux paste in a 10cc syringe, built for tinning and reballing BGA and PGA components on phone mainboards. The syringe has a locking button and a dedicated dispensing needle, so you place flux only where the pads need it. The manufacturer lists it for lead-free soldering, with RoHS compliance and an 18g net weight. You get quick tinning with less smoke and no rinsing step. It suits daily mobile repair work across your bench.
Out of stock
RELIFE RL-420-UV Flux Paste for Lead-Free BGA Work
The RELIFE RL-420-UV flux paste is a light yellow BGA flux made for phone mainboard repair benches. Flux quality decides whether solder wets a pad evenly during reballing and tinning, so this rosin-based paste is formulated for that exact step. The manufacturer lists it for lead-free soldering on mobile phone boards, covering both BGA and PGA components. Each unit arrives as a 10cc syringe with a dedicated dispensing needle, which gives you a practical amount for regular bench work. This page covers where the paste fits in your workflow, how the syringe handles daily use, and what the manufacturer states about smoke, residue, and cleanup.
Where This Paste Fits in the BGA Workflow
Most BGA jobs follow the same sequence: remove the chip, clean the pads, apply flux, tin the pads, and then reball or reseat the component. This paste belongs at the flux step, where it prepares the pad surface and the ball surface for solder. Fine-pitch packages leave little room for error, so match the amount to the size of the pad field. Larger pad areas take slightly more paste, while small packages need only a light film. Apply a thin, even layer across the area rather than a heavy deposit, because excess flux can push solder into neighboring joints. Check the pads after each application and confirm they show a uniform sheen before you place the ball or chip. Pair the flux step with your hot air station, and set the temperature to suit the component and board you are working on.
Syringe Design and Controlled Dispensing
The paste ships in a syringe with a locking button and a dedicated dispensing needle. The locking button holds the plunger steady between applications, so the paste does not leak out while you move between boards. The needle lets you place flux on a single pad or a small cluster instead of spreading it across the whole board. The manufacturer presents this dosing method as a way to cut waste, which matters when one 10cc syringe supports many repairs. Because the needle is dedicated, you avoid cross-contamination with other fluxes on your bench. Label the syringe once you open it, keep the cap on between jobs, and wipe the needle tip before you reseal the unit. These habits keep the paste in better condition across many jobs.
Residue, Smoke and Post-Soldering Cleanup
The manufacturer describes quick tinning with a minimum amount of smoke, which keeps your work area easier to manage during heating. The formula suits no-rinsing use, so you can skip the washing step that many older fluxes require on the board. The product carries RoHS compliance, and the manufacturer states that it leaves minimal residue with high insulation. Insulation matters on mobile boards, where tight trace spacing raises the risk of leakage between neighboring pads. Inspect each joint after cooling, and clean away excess residue only if your repair standard requires it. Lead-free joints often need a different heating profile than leaded work, so record how the paste performs on your common chips. Treat the residue and insulation figures as manufacturer claims, and confirm them on your own boards.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Light yellow rosin-based paste for BGA and PGA work
- ✓10cc syringe with locking button
- ✓Dedicated dispensing needle for controlled application
- ✓Quick tinning with a minimum amount of smoke
- ✓No-rinsing formula
- ✓RoHS compliant
- ✓Designed for lead-free soldering
Specifications
| Brand | RELIFE |
|---|---|
| Model | RL-420-UV |
| Category | BGA Solder Paste Flux |
| Compatibility | Universal, not device-specific |
| Supported Devices | Phone mainboard BGA and PGA components |
| Technology | Lead-free soldering |
| Material | Imported rosin (resin) |
| Dimensions | 35 × 120 mm tube |
Common Repair Uses
- ✓Verified workflows for BGA and PGA soldering on phone boards.
- ✓Tinning BGA pads before chip reseating
- ✓Reballing BGA chips on phone mainboards
- ✓Soldering PGA components on phone boards
- ✓Board-level IC replacement on phone mainboards
- ✓Lead-free soldering on SMD components
Compatible Devices
- ✓Universal, not device-specific. Verified scope covers mobile phone mainboards and BGA/PGA package types.
- ✓Mobile phone mainboards with BGA packages
- ✓PGA components on phone mainboards
- ✓SMD components on mobile boards
- ✓Lead-free BGA reballing and tinning work
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is this flux paste suitable for lead-free BGA soldering?
Does this flux paste need rinsing after soldering?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



