QUICK 960-SK Small Knife Soldering Tip

₨ 1

Small Knife Tip for Drag Soldering and Pin Rework

The QUICK 960-SK is a small knife soldering tip with a 6.5 mm outer diameter and a 4 mm internal bore. Its flat, blade-like head suits drag soldering, clearing solder bridges, and reflowing connector pins where a conical tip gets in the way. It is listed as a replacement for QUICK 969A, 967 and TS1100 soldering stations. Confirm your station model before ordering. Standard packaging is 10 pieces per bag.

Out of stock

19 People watching this product now!
Description

960-SK Small Knife Soldering Tip for Drag Soldering and Pin Rework

The 960-SK small knife soldering tip gives you a flat contact edge for work where a round or conical tip struggles. It helps you drag solder across a row of fine pins, clear bridges on connectors, and touch up pads on crowded boards. Its knife profile concentrates contact along one line, so you decide exactly where solder flows. Treat it as a task-specific tip, not an all-purpose one, and keep the edge tinned so it wets properly from the first stroke.

Where This Tip Fits in Your Rework Workflow

Most board-level jobs follow a sequence: inspect under magnification, remove the fault, clean the pads, then restore connections. The small knife tip fits the middle and finishing stages. After a hot air or manual pass leaves excess solder on a pin row, a knife edge pulls that solder away in one controlled stroke. The same geometry helps when you reflow a connector that lost contact after a drop. It is not the right choice for heating large ground planes, where a bigger tip carries more thermal mass. Keep it beside a conical tip so you switch by task instead of forcing one shape through every repair.

Knife Geometry, Heat Flow and Control

A knife head presents a wider flat face than a pointed tip of similar length. That face transfers heat into a joint quickly when it is in firm contact, which helps you melt existing solder without overheating nearby components. The trade-off is that the flat face can bridge adjacent pins if you carry too much solder onto it. Work with a thin film of solder on the edge, drag at a steady angle, and lift away as soon as the joint flows. Adjust iron temperature in small steps within the range your board and components tolerate, rather than chasing speed.

Station Compatibility and Ordering Checks

Confirm the station before you order. The supplier listing ties the 960-SK to QUICK 969A, 967 and TS1100 soldering stations, and it gives a 6.5 mm outer diameter with a 4 mm internal bore. Check your handle’s seating against those figures before fitting, and never force a tip that does not seat fully. If your bench runs a different QUICK model, confirm compatibility with your supplier first. Plan restock around the standard 10-piece bag.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Small knife tip head for drag soldering and pin rework
  • 6.5 mm outer diameter with 4 mm internal bore
  • RoHS listed

Specifications

BrandQUICK
Model960-SK
CategorySoldering Tips (Tools & Consumables)
CompatibilityQUICK 969A, 967 and TS1100 soldering stations (per supplier listing)
Head ShapeSmall knife tip
DimensionsTip outer diameter 6.5 mm, inner diameter 4 mm

Common Repair Uses

  • Drag soldering fine-pitch pin rows on ICs and connectors
  • Removing solder bridges between adjacent pins after rework
  • Reflowing connector pins that lost contact on the board
  • Touching up pads and joints on crowded PCBs where a conical tip cannot reach

Compatible Devices

  • Verified scope is the QUICK station models named in the supplier listing. Confirm your handle before ordering.
  • QUICK 969A soldering station
  • QUICK 967 soldering station
  • QUICK TS1100 soldering station

FAQ

What is the product name?
The product name is QUICK 960-SK Small Knife Soldering Tip.
What is the brand of this product?
The brand of this product is QUICK.
What is the model of this product?
The model of this product is 960-SK.
What is this product used for?
This product is used for drag soldering, solder bridge removal, and pin reflow on fine-pitch boards.
Which devices are compatible with this product?
This product is listed as compatible with QUICK 969A, 967 and TS1100 soldering stations.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this tip fit the QUICK 960 series stations?
The supplier listing names 969A, 967 and TS1100 stations, not the 960 series. Confirm your station model with the supplier before ordering.
What are the tip’s dimensions?
The tip has a 6.5 mm outer diameter and a 4 mm internal bore.