Relife RL-3520 3.5mm Desoldering Wick 2M Copper Braid
₨ 850
3.5mm Desoldering Wick for Pads and Pin Cleanup
The Relife RL-3520 is a 3.5mm desoldering wick with a 2-meter copper braid, built for wide pads, connector pins and bulk solder removal on mobile boards. The 100% copper braid pulls molten solder in by capillary action, and its halide-free, non-conductive residue does not need to be cleaned off the board. A sealed thumb-wheel dispenser protects the wire from moisture between jobs. Choose this width when a 2.0mm or 2.5mm wick saturates too slowly on larger joints, and keep the 2-meter spool on the bench for repeated passes across a charging port or IC row.
Out of stock
Relife RL-3520 3.5mm Desoldering Wick for Board Rework
The Relife RL-3520 is a 3.5mm desoldering wick supplied in a 2.0-meter length, and it belongs to the bulk-removal stage of board rework. Most repairs that involve lifting or reseating a component start with clearing old solder from the pads, and a wick this wide gives you enough braid contact to draw solder off larger pads without overheating a single point. In a typical mobile repair workflow, you use this 3.5mm desoldering wick after the component is loose and before you tin the pads again. Narrower widths still have their place on fine-pitch work, but the 3.5mm version handles the heavy joints that smaller braids struggle to clear in one pass.
Where the 3.5mm Width Earns Its Place
A 3.5mm braid carries more solder per pass than narrow wicks, which matters on connector shells, larger ground pads and the solder-heavy joints around charging ports. You notice the difference when a thin braid clogs after two passes and leaves a bridge behind. With this width, lay the braid flat over the joint, press the heated tip through the braid, and watch the molten solder climb into the copper. Keep the tip moving and let the braid do the absorbing instead of dragging the wick across the pad. Once the braid turns dull or dark, cut off the saturated section and move to fresh copper. If solder still sits proud of the pad, a second light pass usually finishes the job without lifting the trace.
Low-Residue Copper Braid and Clean-Up Expectations
The braid is 100% copper with a low-residue, no-clean flux. The residue is halide-free and non-conductive, so for many boards you can test the repair without washing the wick residue away first. That makes this wick practical when you move between jobs on a busy bench. A pad that will receive fresh flux or solder paste still benefits from a quick wipe with isopropyl alcohol before reflow, especially on boards with tight spacing. The flux also helps the braid draw solder more readily, so you spend less heat time on the trace. Store the spool away from humidity, because the copper and flux both perform best when the braid stays dry.
Dispenser Care and Workshop Storage
The thumb-wheel dispenser feeds the braid smoothly, so you control the length of each pass with one hand while the iron stays in the other. The sealed body keeps moisture away from the wire, which extends its working life on a humid repair bench. The stainless steel mouth guides the braid to the joint without catching on nearby fine components. Between sessions, return the spool to its sealed position and keep it away from direct heat and open flux containers. Cut the wick only when the saturated section is clear of the work area, and keep a spare spool on hand for longer rework days. Consistent storage habits keep the braid absorbing solder at the same rate from the first pass to the last.
| Weight | 0.9 kg |
|---|
Key Features
- ✓3.5mm braid width for wider pads and heavy solder joints
- ✓2.0m length for extended bench use
- ✓100% copper braid construction
- ✓Low-residue, no-clean, halide-free flux
- ✓Non-conductive residue that does not need board cleaning
- ✓Fine braid weave for strong capillary action
- ✓Thumb-wheel dispenser with stainless steel mouth
- ✓Sealed dispenser protects the wire from moisture
Specifications
| Brand | RELIFE |
|---|---|
| Model | RL-3520 |
| Category | Desoldering Wick |
| Compatibility | Universal, not device-specific |
| Supported Devices | Universal, general SMD, through-hole and pad desoldering |
| Technology | Copper braid with low-residue, no-clean flux |
| Material | 100% copper |
| Dimensions | 3.5 mm width x 2.0 m length |
Common Repair Uses
- ✓Verified workflows where a 3.5mm copper braid clears excess solder from a joint.
- ✓Clearing excess solder from IC pads before reseating or reballing
- ✓Removing bridges between closely spaced charging port pins
- ✓Tidying pads after removing a shield can or connector
- ✓Draining solder from through-hole pads before inserting a replacement component
- ✓Cleaning jumper pads on a board before re-tinning
- ✓Removing solder from a damaged component lead before a clean replacement
- ✓Preparing large ground pads before soldering a new flex cable
- ✓Clearing solder from BGA pads after chip removal, before fresh paste
Compatible Devices
- ✓Universal, not device-specific. Applies to any solder joint that accepts a desoldering wick.
- ✓Through-hole component leads on mobile and PCB boards
- ✓SMD resistor and capacitor pads
- ✓Connector pins and shell solder joints
- ✓IC and BGA pad cleanup after component removal
- ✓Board-to-board connector solder joints
- ✓Shield-can and ground pad solder joints
- ✓Standard copper pads on rigid and flexible PCBs
- ✓Wide pads that need heavy solder removal in one pass
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the RL-3520 leave residue that needs cleaning?
Is a 3.5mm wick suitable for BGA pad cleanup?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



