UV Solder Mask for Motherboard Repair | Relife RL-UVH902

₨ 1

UV Solder Mask for Quick Motherboard Repairs

The Relife RL-UVH902 is a 10cc UV-curing solder mask that sets in about three seconds under a UV lamp. You apply it to insulate fresh jumper wire work, protect exposed pads, and rebuild damaged mask on a motherboard. Once cured, the layer holds firm and resists high temperatures, so it stays in place through the rest of your rework. Use it on your bench when a board needs fast insulation, not a long drying wait.

Out of stock

15 People watching this product now!
Description

UV Solder Mask Workflow for Motherboard Repair

The Relife RL-UVH902 is a UV solder mask for motherboard repair that cures in about three seconds under a UV lamp. In a typical jumper lagana job, you apply it after a wire or component fix to insulate the exposed area and lock the pad in place before the board returns to service. Its fast cure matters on a busy repair bench, because the board moves to the next step without waiting for a slow-drying mask to set. The 10cc syringe format suits manual glue guns, which gives you controlled placement around small pads and tight IC edges. Your sequence stays simple: apply the mask, expose it to UV light, inspect the coverage, and continue the repair with confidence. Use it when you need a finished, insulated surface in seconds rather than minutes on a crowded mobile board that leaves little room for error.

Where This Mask Fits in Your Repair Sequence

Most motherboard rework ends with insulation, because bare copper around a fresh jumper can short against neighboring pins once the board powers up. The RL-UVH902 covers tail plugs, screw posts, and welding pads, which are common trouble spots on mobile boards that take heavy handling. It also secures enamelled wire, so a fine coil stays flat and does not lift during the next step on your bench. Apply the mask in a thin, controlled layer over the repaired area, and avoid spreading it onto nearby test points you still need to reach. Cure the layer under UV before you flip the board or reflow another component, so the fixed part holds its position. This sequence keeps the repair clean, protects the surrounding components, and saves you from repeat visits to the same board.

Curing Speed and Application Technique

The manufacturer rates the cure at three seconds under UV light, which makes this mask practical for a fast, repeatable bench rhythm. You need a UV lamp to start the curing reaction, so keep one within reach of your station and position it close to the work area that sits near the board. Because the mask cures without leaving dead corners, the coverage across your repaired area stays consistent from edge to edge. Apply it in a thin, even layer rather than a heavy bead, since thinner films expose more evenly and set more reliably under the lamp. Check that the surface is fully hard and no longer tacky before you handle the board or move to reflow. Then inspect the edges for any gap that needs a second pass, rather than assuming the first layer covered everything.

Color Range and Heat Performance

The RL-UVH902 range includes black, green, red, and blue, which helps when you map multiple repair zones on one board. Confirm the exact shade on the product page before ordering, because listings across the series are not always identical. The manufacturer describes the cured layer as high-temperature resistant and non-softening under normal rework heat. No exact temperature rating is published, so treat the cured mask as insulation and protection rather than a load-bearing structure. Plan your soldering so the mask never sees heat beyond what your station and the board actually need during the repair. Keep unused syringes capped and stored away from direct light to protect the material between jobs.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • 3-second UV curing for fast turnaround
  • High-temperature resistant insulation layer once cured
  • Strong adhesion that stays fixed after curing
  • No dead corners during curing
  • Fits tail plugs, screw posts, and welding pads
  • Repairs peeling or damaged PCB solder mask
  • Secures enamelled wire and jumper coils
  • 10cc syringe format for controlled application

Specifications

BrandRelife
ModelRL-UVH902
CategoryPCB Repair Equipment
CompatibilityUniversal, not device-specific
TechnologyUV curing
Dimensions28 x 35 x 100 mm

Common Repair Uses

  • Insulating jumper wires after a board repair
  • Fixing tail plugs and screw posts to the board
  • Securing welding pads that lift or weaken
  • Restoring peeling or damaged solder mask on a PCB
  • Fixing enamelled wire in place
  • Protecting components after soldering
  • Covering exposed copper near fresh repairs
  • Insulating and protecting the circuit area after rework

Compatible Devices

  • Universal, not device-specific. Verified scope covers mobile phone motherboard and PCB repair work, not a specific model list.
  • Universal, not device-specific
  • Mobile phone motherboards (general PCB scope)
  • Pads and solder mask areas on rigid circuit boards
  • Enamelled wire and fine coil fixing points
  • Tail plug and screw post areas on mobile boards
  • Jumper wire insulation zones
  • Components on rework benches that need insulation
  • Mobile repair and PCB rework workstations

FAQ

What is the product name?
The product name is Relife RL-UVH902 3S Quick-Solder Mask for Motherboard Repairs.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is RL-UVH902.
What is this product used for?
This product is used to insulate jumper wires, secure tail plugs and screw posts, and repair damaged solder mask on motherboards.
Which devices are compatible with this product?
This product is universal and not device-specific, and it applies to mobile phone motherboard and PCB repair work.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Do I need a UV lamp to cure RL-UVH902?
Yes, the mask is a UV-curing product and needs a UV light source to cure in about three seconds.
Is RL-UVH902 heat resistant after curing?
The manufacturer describes the cured layer as high-temperature resistant, but no exact temperature rating is published.