Aifen A5 Edition T210 Soldering Iron Station 120W

₨ 12,000

Aifen A5 T210 Soldering Station for Board-Level Repair

The Aifen A5 is a 120W soldering station with digital temperature control from 100°C to 450°C. It uses the standard T210 handle and supports C115, C210 and C245 tip series, so you can handle SMD components, IC replacement and jumper work from one bench setup. The station supports lead-free solder and wire control functionality, and an optional T210 wire-control handle is available. A clear digital display helps you set and confirm temperature before every joint. It suits mobile repair technicians and repair shops that need a dependable station for daily phone and PCB work.

Out of stock

13 People watching this product now!
Description

Aifen A5 T210 Soldering Station for Precision Mobile Repair

The Aifen A5 T210 soldering station puts a 120W digital station at the center of your repair bench, paired with the standard T210 handle that accepts C115, C210 and C245 tip series. If you handle board-level work on phones, tablets and PCBs, this station gives you controlled heat from 100°C to 450°C, which covers both standard and lead-free solder work. Many older stations leave you guessing from a dial, but the digital display shows the set temperature so you can match the tip to the joint. This guide explains where the station fits in your workflow, how the handle and tip system works, and which jobs suit it best.

Where This Station Fits in Your Repair Workflow

Every board-level job starts with diagnosis, and the soldering station comes into play once you move from testing to physical intervention. You isolate the faulty component with a multimeter and a microscope, then decide whether the fault needs a simple reflow, a component swap or a pad repair. The A5 handles each of these stages at the bench, because its 120W output recovers temperature quickly after a joint absorbs heat. Your sequence usually follows a clear order: heat the joint, remove the part, clean the pads, then place and solder the replacement. The station supports this sequence without forcing you to switch equipment between steps. Pair it with a PCB holder for stable boards and a microscope for fine-pitch inspection, and the whole bench works as one connected setup.

Handle and Tip System Explained

The station uses the standard T210 handle, a slim and lightweight grip built around the C210 tip series. The short distance from tip to grip gives you better control at fine pitch, which matters when you work near connectors and small surface-mount parts. Because the handle uses cartridge-style tips, you change the tip shape without rebuilding the iron, so one station covers bent and knife profiles as each job requires. The station also accepts C115 and C245 tip series, which expands your options for heavier joints that need more thermal mass. If your workflow calls for wire control, Aifen offers an optional T210 wire-control handle that works with the same station. Always confirm the tip series before ordering replacements, because a tip that fits the mechanical size of the handle but belongs to a different series will not seat correctly.

Temperature Control and Lead-Free Solder Handling

The A5 operates across a 100°C to 450°C range, which spans low-temperature rework and the higher heat that lead-free solder requires. Lead-free alloys melt at higher temperatures and oxidize faster, so you need a station that recovers quickly and holds a steady setpoint. The digital display lets you set the target temperature precisely and read it at a glance, which is far more reliable than estimating from a dial. For a technician who alternates between leaded and lead-free boards, that precision lowers the risk of lifting pads or damaging components. Set the temperature to the lowest value that melts the joint cleanly, then raise it in small steps only if the solder does not flow. Keep the tip tinned between joints and wipe it on a clean sponge rather than letting oxide build up. A well-tinned tip transfers heat efficiently, so each joint takes less total heat.

Common Board-Level Jobs on Your Bench

Most of the work this station handles falls into a few familiar categories. IC replacement is the most demanding, because the chip sits on dense pads and you need even heat across every leg. For jobs like replacing a charging port or a microphone component, the station provides the controlled heat to remove the part without disturbing nearby components. Jumper-level repairs, where you bridge a damaged trace or restore a power line, depend on clean pads and a tip that transfers heat without flooding the joint. Passive component swaps, such as a resistor or capacitor on a power rail, reward precision more than raw heat. Your bench will usually see these tasks mixed together throughout the day, so the station must move quickly from fine work to heavier joints without a change of equipment.

Setting Up Your Station for Long-Term Use

Place the station on a heat-resistant mat in a spot with good airflow and clear space around the stand. Return the handle to its holder whenever you pause, so the hot tip never touches your bench or cables. Check the cable and handle connection before each session, and replace a damaged handle rather than working around a loose connection. Clean the tip regularly, and replace it once the plating wears through or the tip stops accepting solder even after cleaning. Store spare tips in a dry box to prevent oxidation, and label them by series so you always pick the correct fit for each handle. These habits extend the life of your handle and keep the station responding consistently across every job.

Additional information
Weight1.0 kg
Q & A
Please login to post questions

Key Features

  • 120W power output for fast heat recovery
  • Digital temperature control from 100°C to 450°C
  • Clear digital display for setpoint and temperature readout
  • Compatible with C115, C210 and C245 tip series
  • Standard T210 handle for precision work
  • Optional T210 wire-control handle
  • Wire control function support
  • Suitable for lead-free soldering

Specifications

BrandAifen
ModelA5
CategorySoldering Station
CompatibilityC115, C210 and C245 tip series
TechnologyDigital display, temperature control, wire control support
Power Rating120W
Weight928g

Common Repair Uses

  • IC replacement on phone motherboards
  • SMD resistor and capacitor replacement on power rails
  • Charging port and connector rework
  • Jumper-level trace bridging and power line repair
  • Removing and reinstalling board-level components during dead phone diagnosis
  • Pad cleanup and repair after component removal
  • Lead-free solder joints on modern mobile boards
  • General PCB rework at the repair bench

Compatible Devices

  • Verified tip and handle scope. The station is not device-specific and works as a general-purpose station for any task that uses these tip series.
  • Standard T210 handle
  • Optional T210 wire-control handle
  • C210 series soldering tips
  • C115 series soldering tips
  • C245 series soldering tips
  • Lead-free solder work
  • Mobile phone and tablet board-level repair (general scope, not device-specific)
  • PCB and SMD component repair (general scope, not device-specific)

FAQ

What is the product name?
The product name is Aifen A5 Edition T210 Soldering Iron.
What is the brand of this product?
The brand of this product is Aifen.
What is the model of this product?
The model of this product is A5.
What is this product used for?
This product is used for soldering, desoldering and rework of SMD components, ICs and PCB joints.
Which devices are compatible with this product?
This product is compatible with C115, C210 and C245 soldering tip series using the standard T210 handle.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which tip series does the Aifen A5 support?
The Aifen A5 supports C115, C210 and C245 tip series, with the standard T210 handle.
Does the Aifen A5 support a wire-control handle?
Yes, the station supports wire control functionality, and an optional T210 wire-control handle is available.