Easy JTAG Plus Box With ISP Adaptor for eMMC & JTAG
₨ 115,000
Easy JTAG Plus ISP Programmer Box
The Easy JTAG Plus Box with ISP adapter gives your bench one USB-connected box for eMMC ISP, JTAG, SPI and NAND service work. Z3X built it around a SAM3X8E host CPU and a Spartan-6 FPGA, and the ISP 1-bit and ISP 4-bit boards let you reach eMMC memory directly on the PCB. You skip the full chip-off and still repair boot faults, recover data and rebuild damaged partitions. The box also reads JTAG test points, so a dead phone with a damaged pad stays repairable. Pakistani technicians who run a daily flash and boot-repair queue get a programmer built for precise, repeatable work.
In stock
Easy JTAG Plus Box with ISP Adapter: eMMC ISP and JTAG Programmer
The Easy JTAG Plus Box with ISP adapter belongs on benches that handle memory-level faults every day. Z3X designed the second-generation hardware as a universal service tool. It talks to eMMC, ISP, JTAG, SPI and NAND interfaces from one box, and a single USB A-B cable connects it to your Windows PC. For a dead phone that no flash box can wake, the ISP adapter gives you a board-level route into the eMMC without lifting the chip.
Hardware Platform and Interface Speed
The box runs on a SAM3X8E host CPU with a Spartan-6 FPGA, and digital PWM control manages its power logic. Z3X rates the box-to-PC link at up to 40 MB/s. ISP transfers reach up to 4 MB/s in 1-bit mode and up to 12 MB/s in 4-bit mode on eMMC 5.0 and newer chips. Z3X also increased the JTAG interface speed by 20% over the first generation. A VCC/VCCQ switch with overcurrent protection and a smart fuse with a 0.5A threshold guard the board you are probing, so a wrong pinout does not take a second component with it.
ISP Adapter Set and Direct eMMC Access
The adapter set includes JTAG, ISP 1-bit, ISP 4-bit, U-socket and E-socket boards. You solder the ISP lead to the CMD, CLK, DAT0, VCC and VCCQ test points, power the board through the box, and read or write the eMMC in place. The new hardware also runs adapter-less ISP, since the supporting circuitry sits inside the box. Your older Easy JTAG G1 ISP 1-bit adapters keep working with it, so existing accessories stay in service. Pair this box with a hot air station and a microscope when a board needs a tidy joint on a small test point.
Repair Workflow Fit for Pakistani Workshops
Most memory faults reach your bench as dead after flash, hang on logo, boot loop issue or a phone that refuses to charge or power on. The Easy JTAG Plus software handles these in automatic one-click mode or in manual mode when you want full control. You can repair boot sectors, rebuild eMMC firmware structures, manage partitions, recover user data and program SPI memory chips. A built-in eMMC Android file browser lets you pull customer photos and contacts before you touch the firmware. On a hardware fault, you confirm the memory first with the box, then do IC change karna or jumper lagana only where the board needs it. A multimeter, a PCB holder and a reballing kit sit naturally beside this programmer in your repair line-up.
JTAG Finder and Protocol Coverage
JTAG mode includes a pin finder, so a board with scratched or missing pads does not stop the job. The firmware lists ARM7, ARM9 and ARM11 cores, plus PXA270, PXA3xx, OMAP850, Cortex-A8 and dual-core Cortex-A9 targets. The box reads and writes SD cards and NAND memory as well. Z3X built the hardware ready for newer protocols, and UFS socket adapters are available as separate accessories if your queue includes UFS devices. Check your intended chip against the supported list in the Easy-JTAG software before you order extra sockets.
Why Technicians Choose This Programmer
You get a box that behaves the same way on the hundredth phone as on the first. Plug and play drivers install on Windows 8, 8.1 and 10, and the tool also runs on XP, Vista, 7 and 11. When your shop moves from basic flashing toward real chip-level service, this programmer closes the gap between a box chalana routine and genuine eMMC repair. Browse our eMMC programmers, ISP pinout tools and UFS adapters to build a complete memory-repair station around it.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Z3X second-generation hardware with SAM3X8E CPU and Spartan-6 FPGA
- ✓eMMC, ISP, JTAG, SPI and NAND support in one box
- ✓ISP 1-bit and ISP 4-bit adapter boards for direct board-level eMMC access
- ✓Adapter-less ISP design with the circuitry inside the box
- ✓Up to 40 MB/s box-to-PC speed
- ✓Up to 12 MB/s ISP 4-bit speed on eMMC 5.0+ chips
- ✓VCC/VCCQ switch with overcurrent protection and a 0.5A smart fuse
- ✓Compatible with older Easy JTAG G1 ISP 1-bit adapters
Specifications
| Brand | Z3X (Easy-JTAG) |
|---|---|
| Model | Easy-JTAG Plus |
| Category | eMMC / ISP / JTAG Programmer Box |
| Compatibility | Windows XP, Vista, 7, 8, 10, 11 |
| Supported Devices | eMMC-based Android phones via ISP; ARM-core devices via JTAG; SPI memory chips; SD cards; NAND memory |
| Technology | SAM3X8E host CPU, Spartan-6 FPGA, eMMC / ISP / JTAG / SPI / NAND interfaces, USB A-B connection |
Common Repair Uses
- ✓The box covers memory-level service work on dead, bricked and corrupted phones.
- ✓Reviving a dead phone through the ISP test points
- ✓Fixing a dead-after-flash phone
- ✓Clearing hang on logo and boot loop issue faults
- ✓Repairing damaged eMMC boot sectors and firmware structures
- ✓Rebuilding eMMC partitions
- ✓Recovering user data from a phone that cannot boot
- ✓Reading and writing SPI memory chips
- ✓Locating JTAG test points on boards with damaged pads
Compatible Devices
- ✓Compatibility is chip- and interface-based, not brand-based. The scope covers the memory types and processor cores below.
- ✓eMMC memory reached through ISP 1-bit
- ✓eMMC 5.0+ memory reached through ISP 4-bit
- ✓eMMC chips mounted in compatible BGA sockets through the U-socket and E-socket adapters
- ✓JTAG targets with ARM7 cores
- ✓JTAG targets with ARM9 and ARM11 cores
- ✓JTAG targets with Cortex-A8 and dual-core Cortex-A9 cores
- ✓PXA270, PXA3xx and OMAP850 platforms
- ✓SPI memory chips and SD cards



