2UUL DA14 Hand Finish Blade Model-S (4 Blades, No Handle)
₨ 1,300
2UUL DA14 S Model Blade, 4-Pack
The 2UUL DA14 S model blade pack gives you four hand-finished blades for separating CPU and NAND flash chips on mobile phone motherboards. Each blade uses 2UUL’s double-sided uniform trimming and a thin-to-thick profile, so your pressure spreads evenly along the edge. You also use it to remove screen glue, lift screen ICs, and free small motherboard parts. The pack contains blades only, so you need a blade handle on your bench. Mechanicpk supplies the DA14 across Pakistan for technicians, repair shops, and service centers.
In stock
2UUL DA14 S Model Blade for CPU and NAND Separation
The 2UUL DA14 S model blade gives your bench a dedicated pry edge for CPU and NAND flash work on mobile phone motherboards. 2UUL supplies the pack as four Model-S blades without a handle, so you restock sharp edges without buying another handle. Pakistani workshops that rework logic boards every day use this blade when they need the same edge geometry on every job.
What the Model-S Profile Does
2UUL designed the S blade in its Hand Finish range to separate the CPU from the NAND flash. You slide the thin leading edge into the gap at the chip edge once your hot air has softened the bond, then work the blade along the side until the chip releases. The blade runs from thin to thick, so the force you apply spreads evenly instead of concentrating at one point. 2UUL describes the double-sided uniform trimming as a patented utility-model technology, and that design defines how this blade behaves in your hand.
Each blade carries a hand-finished edge, which matters when you slip a blade under a chip next to small neighboring components. You control the depth of every push, and you decide when to heat again. That control keeps the job predictable on boards where you cannot afford a slip.
Where It Fits in Your Repair Workflow
Take a dead phone with a suspected CPU or NAND hardware fault. You heat the board with your hot air station, separate the chip with the DA14, clean the pads with your soldering station, inspect them under a microscope, and prepare the chip with a reballing kit. The DA14 handles the separation step in that sequence. A PCB holder locks the board while you work, and a multimeter confirms your results before you close the phone.
The same blade supports eMMC and UFS operations. After you lift a storage chip, you move to your eMMC programmer, UFS adapter, or ISP pinout tool for reading, data recovery, or reprogramming. Technicians who handle dead after flash boards and hang on logo cases often reach for a separation blade before any programming step starts. A test box then checks that the board powers up again after reassembly.
When a job needs IC change karna on a CPU or NAND position, the quality of the separation sets the quality of everything after it. Clean separation leaves less cleanup work on the pads, and that shortens your reballing time.
Screen Glue and Small Component Jobs
2UUL also positions the Model-S blade for removing glue from screens and for lifting screen ICs. You use the same edge to free small motherboard parts such as separators and chips. A display problem or charging issue board often needs glue cleared from around a small IC before you can reach the part, and a thin blade gets into that gap without forcing the board.
Why Stock the Pack Without a Handle
Four blades per pack gives your workshop spare edges for busy weeks. You buy the DA14 when you need replacement Model-S edges, and you keep your handle spend separate. The pack contains blades only, so confirm that you own a blade handle before you order. Repair shop owners who run several benches often stock the S model in quantity, because separation work repeats across every station.
Mechanicpk lists the DA14 for technicians across Pakistan who want a specialist CPU and NAND separation blade at the board-repair level. If you build your bench around the 2UUL Hand Finish range, pair this pack with the other Model blades in the series for glue removal and edge cleaning.
| Weight | 0.6 kg |
|---|
Key Features
- ✓Model-S profile for separating the CPU from the NAND flash
- ✓Double-sided uniform trimming, 2UUL utility model patented technology
- ✓Thin-to-thick blade profile for even force
- ✓Hand-finished edge for controlled pry work
- ✓Four blades in every pack
- ✓Sold without a handle, so you restock blades only
- ✓Suits screen glue removal and screen IC lifting
- ✓Frees small motherboard parts such as separators and chips
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA14 |
| Category | CPU and IC Opening Blades |
| Compatibility | Universal blade for mobile phone motherboard CPU, NAND flash, and screen IC work — not device-specific |
| Technology | Double-sided uniform trimming (utility model patented technology), thin-to-thick blade profile |
| Pack Contents | 4 x Model-S blades (handle not included) |
Common Repair Uses
- ✓Chip separation and glue removal on mobile phone motherboards
- ✓Separating the CPU from the NAND flash
- ✓Prying CPU and NAND chips off the board
- ✓Removing glue from screens
- ✓Lifting screen ICs
- ✓Freeing small motherboard parts such as separators and chips
- ✓Clearing edge glue around ICs before an IC change karna job
- ✓Opening up dead phone and hardware fault boards for chip-level repair
- ✓Restocking Model-S edges in busy workshops
Compatible Devices
- ✓Universal — works on mobile phone motherboards; 2UUL does not publish a device-specific list
- ✓Mobile phone CPU chips
- ✓NAND flash chips
- ✓Screen ICs
- ✓Small motherboard components such as chips and separators
- ✓BGA-package chips on mobile phone logic boards
- ✓Glued screen edges
- ✓Chips bonded with edge glue on mobile phone motherboards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the 2UUL DA14 S model blade separate NAND flash from the CPU?
Does the 2UUL DA14 pack include a handle?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



