2UUL Hand Finish Blades E Model 4Pcs Set Without Handle
₨ 1,400
2UUL E Model Blade Set for CPU and IC Lifting
The 2UUL E model blade set gives your repair bench four thin, hand-finished blades for lifting CPUs, screen ICs and small board components once heat has softened the glue. A bent-blade profile spreads the force across the edge, which reduces damage to the motherboard, the chip and the screen. Each blade tapers from a 0.06mm tip to roughly 0.3mm at the tail and carries a nano-coating against rust. The pack ships without a handle, so you pair the blades with the holder already on your bench. Mechanicpk supplies the 2UUL E model blade set to repair shops across Pakistan.
In stock
2UUL E Model Blade: Thin Prying Precision for Board-Level Rework
The 2UUL E model blade targets the step that follows heat in board-level rework: separating a CPU, screen IC or small component from the motherboard without gouging pads or cracking silicon. Each pack contains four hand-finished blades and no handle, so you build the tool around the holder you already trust. You also use the same blades to clear hardened glue from the screen side. If your bench handles frequent IC change karna jobs, a thin, controlled edge saves boards that thicker pry tools damage.
Bent-Blade Geometry and Nano-Coated Steel Edge
The blade tapers from a tip of about 0.06mm to a tail of about 0.3mm. That thin-to-thick profile spreads pressure evenly along the blade, so the force on the chip stays steady instead of concentrating at one point. 2UUL upgraded this model to a bent-blade design. The bend lets you slide under a chip edge at a shallow angle, which lowers the contact load on the motherboard, the chip and the screen. The result is fewer lifted pads and a better yield on repairs that leave no margin for error.
The blade body stays flexible, thin and elastic. It bends slightly under load and returns to shape, so it does not snap or kink as stiff improvised tools do. A nano-coating protects the metal against rust, which matters in humid workshops where flux, isopropyl alcohol and cleaning fluids sit on the bench all day. The edge is double-sided with uniform trimming, so you can work from either face of the blade.
Where the E Model Fits in Your Rework Workflow
Start with a stable board. Clamp it in your PCB holder, preheat the area and bring the target chip to temperature with your hot air station under the microscope. Once the underfill or edge glue softens, slide the E model blade under the chip edge and lift in small increments. Never force the blade through cold glue. A patient lift protects the pads, and a clean lift leaves the pad field ready for cleaning, flux and reballing.
You use the same blade for screen-side work. It removes glue from the screen and helps separate small parts such as separators and chips. In a hardware fault case such as a dead phone, a charging issue or a display problem, this lets you reach the faulty IC without damaging neighbouring components. It also helps on motherboard-level jobs where you inspect, clean and reflow before you decide whether the board needs a replacement part.
Choosing This Blade Pack for Your Bench
The pack contains four blades and no handle. Confirm that your existing holder fits the blade shank before you order, and keep a spare blade set on the bench so a dull edge never forces you to improvise mid-job. For repair shops and service centers that run several rework jobs a day, a four-blade pack covers a full week of lifting and glue clearing.
2UUL also sells other blade models for different jobs. The S model targets CPU and IC prying, so many technicians keep E and S blades together and select by chip size and glue hardness. Pair either model with a soldering station, a reballing kit and a good microscope, and the blade set becomes one link in a complete IC replacement chain. That chain runs from heat, through lift and clean, to reball and test. Mechanicpk stocks the E model blade set as a distributor line for Pakistan’s repair market.
| Weight | 0.6 kg |
|---|
Key Features
- ✓Four hand-finished blades in one pack
- ✓Bent-blade design that reduces load on motherboard, chip and screen
- ✓Thin-to-thick taper with even force distribution
- ✓Tip thickness of about 0.06mm
- ✓Flexible, elastic blade body that returns to shape
- ✓Nano-coating against rust
- ✓Double-sided uniform trimming
- ✓Handle-free pack that pairs with your own holder
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA15 E Model |
| Category | Mobile Repair Blades |
| Compatibility | Universal for mobile phone motherboard and screen rework, not device-specific |
| Technology | Bent-blade design, nano-coated anti-rust surface |
| Blade Thickness | Tip approx. 0.06mm, tail approx. 0.3mm |
| Pack Contents | 4 blades, without handle |
Common Repair Uses
- ✓Verified use cases for the E model blade in a workshop.
- ✓CPU removal after heating with a hot air station
- ✓Screen IC removal
- ✓Lifting small board parts such as separators and chips
- ✓Glue removal from the screen
- ✓Clearing hardened adhesive around chip edges
- ✓IC change karna on boards with a hardware fault
- ✓Dead phone board inspection and rework
- ✓Pad preparation before cleaning and reballing
Compatible Devices
- ✓Universal scope. The blades work on mobile phone motherboards and screens that need CPU, IC or glue removal, and the tool is not tied to specific models.
- ✓Mobile phone motherboards, universal and not model-specific
- ✓CPU and SoC chips after heat softens the glue
- ✓Screen ICs
- ✓Small board parts such as separators and chips
- ✓Screen-side glue areas
- ✓Android phone boards that need IC-level rework
- ✓Tablet and gadget boards that need careful prying
- ✓Boards you prepare for reballing
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How thin is the blade tip of the 2UUL E model?
Does the 2UUL E model blade set include a handle?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



