2UUL Y Model Underfill Glue Cutting Blades 4 Pack
₨ 1,400
Underfill Glue Cutting Blade Set
The 2UUL Y Model is an underfill glue cutting blade built for one job: slicing the black underfill that locks CPU and memory chips to a smartphone logic board. Each pack contains 4 blades and ships without a handle, so you pair the blades with the holder already on your bench. The Y Model cuts the underfill without hurting the motherboard, which makes it a practical choice for chip-off prep, BGA rework and pad protection. You still need a hot air station, a PCB holder and a microscope for the full job, but this blade does the cutting. Keep a spare pack on your repair bench so a dull edge never stops a board.
In stock
Underfill Glue Cutting Blade for Chip-Level Mobile Repair
An underfill glue cutting blade decides whether a chip lifts clean or tears pads off the board. The 2UUL Y Model gives you a dedicated blade for cutting the black underfill around smartphone CPU and memory chips without hurting the motherboard. The pack contains 4 blades and no handle, so you build the set around the holder you already trust. Mechanicpk stocks this blade set for Pakistani repair shops that handle board-level work daily and want a consumable they can reorder by the pack.
Where the Y Model Sits in the 2UUL Blade Range
2UUL organizes its hand finish blades by letter model, and each letter covers a different task. The S Model separates the CPU and NAND flash, the E Model removes glue from the motherboard IC and CPU, and the X Model works as an edge glue removal tool. The Y Model covers underfill cutting: it cuts the black underfill glue without hurting the motherboard. Pick the Y Model when the underfill itself blocks the chip, not when you only need to clear a glued edge. Check the model letter against the job on your bench before you order, because a wrong letter wastes a pack.
Underfill Cutting in a Real Chip-Off Workflow
Underfill is the hardened epoxy manufacturers flow around chips to lock them against drop damage. On a dead phone with a hardware fault, that glue sits between you and the chip you need to replace. Most technicians start by securing the board in a PCB holder and softening the underfill with controlled heat from a hot air station. Then they work the blade along the chip edge under a microscope. The Y Model cuts through the black glue, so you free the chip and keep the pads intact for the next stage.
After the chip lifts, you clean the pads and move to your reballing kit and soldering station for the reinstall. The same prep applies when you plan an IC change karna job on an eMMC or UFS chip. It also applies when a phone goes dead after flash and the storage chip needs a clean board before you read it through ISP pinout tools or an eMMC programmer. Cut the underfill first and you protect every step that follows.
Pack Contents and Bench Stocking
Each pack holds 4 blades of the Y Model and no handle. A handle-less set suits workshops that already own a holder and want to refill blades without paying for another handle. If you do not own a holder yet, buy one separately before your first job. Edge condition matters on underfill work, because a worn edge forces extra pressure, and extra pressure near BGA pads puts the board at risk. Swap in a fresh blade when cutting starts to feel harder than it should.
Once the rework finishes, verify the board with a multimeter and a test box before you close the phone. Buyers who handle boot loop issue repairs, charging issue boards and display problem boards at the chip level will find the Y Model a steady, low-cost consumable. Pair it with the S, E and X Models when your bench covers separation, glue removal and edge cleaning as well as underfill cutting.
| Weight | 0.6 kg |
|---|
Key Features
- ✓Y Model blade dedicated to cutting black underfill glue
- ✓Cuts underfill without hurting the motherboard
- ✓4 blades per pack
- ✓Sold without handle, so it fits your existing holder setup
- ✓Part of the 2UUL hand finish blade range
- ✓Universal manual tool, not tied to one phone model or chipset
- ✓Works alongside hot air stations, PCB holders and microscopes in chip-off workflows
- ✓Pairs with the S, E and X Models for separation, glue removal and edge cleaning
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL Y Model Underfill Glue Cutting Blades (4 pcs, without handle) |
| Technology Entity | Hand finish blades, underfill glue cutting |
| Compatible Device Entities | Smartphone logic boards, NAND flash, eMMC, UFS, CPU/SoC chips, iPhone, Samsung, Oppo, Vivo, Infinix, Tecno |
| Repair Process Entity | Chip-off preparation, BGA rework, underfill cutting, pad protection |
| Industry Entity | Mobile phone repair, PCB repair, GSM repair Pakistan |
Common Repair Uses
- ✓Cutting black underfill glue around chips before chip removal, rework or reballing.
- ✓Cutting black underfill around CPU chips
- ✓Exposing chip edges before hot air lifting
- ✓Chip-off prep for NAND, eMMC and UFS replacement
- ✓Dead phone board-level repair
- ✓Storage chip replacement on phones dead after flash
- ✓Hardware fault repair on boot loop boards
- ✓Pad protection during BGA chip removal
- ✓Logic board refurbishment
Compatible Devices
- ✓Universal manual tool, not device-specific. It suits any board with underfill glue around the chips; the families below show where technicians meet underfill most often.
- ✓Smartphone logic boards with underfilled CPU/SoC chips
- ✓Underfilled NAND flash chips
- ✓eMMC and UFS storage chips with black underfill
- ✓iPhone logic boards
- ✓Samsung logic boards
- ✓Oppo and Vivo logic boards
- ✓Infinix and Tecno logic boards
- ✓Tablet and other small electronics PCBs with underfilled chips
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the 2UUL Y Model blade pack include a handle?
What is the difference between the 2UUL Y Model and the S, E and X Models?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



