2UUL Hand Finish Blades E Model 4Pcs Set Without Handle

₨ 1,400

2UUL E Model Blade Set for CPU and IC Lifting

The 2UUL E model blade set gives your repair bench four thin, hand-finished blades for lifting CPUs, screen ICs and small board components once heat has softened the glue. A bent-blade profile spreads the force across the edge, which reduces damage to the motherboard, the chip and the screen. Each blade tapers from a 0.06mm tip to roughly 0.3mm at the tail and carries a nano-coating against rust. The pack ships without a handle, so you pair the blades with the holder already on your bench. Mechanicpk supplies the 2UUL E model blade set to repair shops across Pakistan.

In stock

13 People watching this product now!
Description

2UUL E Model Blade: Thin Prying Precision for Board-Level Rework

The 2UUL E model blade targets the step that follows heat in board-level rework: separating a CPU, screen IC or small component from the motherboard without gouging pads or cracking silicon. Each pack contains four hand-finished blades and no handle, so you build the tool around the holder you already trust. You also use the same blades to clear hardened glue from the screen side. If your bench handles frequent IC change karna jobs, a thin, controlled edge saves boards that thicker pry tools damage.

Bent-Blade Geometry and Nano-Coated Steel Edge

The blade tapers from a tip of about 0.06mm to a tail of about 0.3mm. That thin-to-thick profile spreads pressure evenly along the blade, so the force on the chip stays steady instead of concentrating at one point. 2UUL upgraded this model to a bent-blade design. The bend lets you slide under a chip edge at a shallow angle, which lowers the contact load on the motherboard, the chip and the screen. The result is fewer lifted pads and a better yield on repairs that leave no margin for error.

The blade body stays flexible, thin and elastic. It bends slightly under load and returns to shape, so it does not snap or kink as stiff improvised tools do. A nano-coating protects the metal against rust, which matters in humid workshops where flux, isopropyl alcohol and cleaning fluids sit on the bench all day. The edge is double-sided with uniform trimming, so you can work from either face of the blade.

Where the E Model Fits in Your Rework Workflow

Start with a stable board. Clamp it in your PCB holder, preheat the area and bring the target chip to temperature with your hot air station under the microscope. Once the underfill or edge glue softens, slide the E model blade under the chip edge and lift in small increments. Never force the blade through cold glue. A patient lift protects the pads, and a clean lift leaves the pad field ready for cleaning, flux and reballing.

You use the same blade for screen-side work. It removes glue from the screen and helps separate small parts such as separators and chips. In a hardware fault case such as a dead phone, a charging issue or a display problem, this lets you reach the faulty IC without damaging neighbouring components. It also helps on motherboard-level jobs where you inspect, clean and reflow before you decide whether the board needs a replacement part.

Choosing This Blade Pack for Your Bench

The pack contains four blades and no handle. Confirm that your existing holder fits the blade shank before you order, and keep a spare blade set on the bench so a dull edge never forces you to improvise mid-job. For repair shops and service centers that run several rework jobs a day, a four-blade pack covers a full week of lifting and glue clearing.

2UUL also sells other blade models for different jobs. The S model targets CPU and IC prying, so many technicians keep E and S blades together and select by chip size and glue hardness. Pair either model with a soldering station, a reballing kit and a good microscope, and the blade set becomes one link in a complete IC replacement chain. That chain runs from heat, through lift and clean, to reball and test. Mechanicpk stocks the E model blade set as a distributor line for Pakistan’s repair market.

Additional information
Weight0.6 kg
Q & A
Please login to post questions

Key Features

  • Four hand-finished blades in one pack
  • Bent-blade design that reduces load on motherboard, chip and screen
  • Thin-to-thick taper with even force distribution
  • Tip thickness of about 0.06mm
  • Flexible, elastic blade body that returns to shape
  • Nano-coating against rust
  • Double-sided uniform trimming
  • Handle-free pack that pairs with your own holder

Specifications

Brand2UUL
ModelDA15 E Model
CategoryMobile Repair Blades
CompatibilityUniversal for mobile phone motherboard and screen rework, not device-specific
TechnologyBent-blade design, nano-coated anti-rust surface
Blade ThicknessTip approx. 0.06mm, tail approx. 0.3mm
Pack Contents4 blades, without handle

Common Repair Uses

  • Verified use cases for the E model blade in a workshop.
  • CPU removal after heating with a hot air station
  • Screen IC removal
  • Lifting small board parts such as separators and chips
  • Glue removal from the screen
  • Clearing hardened adhesive around chip edges
  • IC change karna on boards with a hardware fault
  • Dead phone board inspection and rework
  • Pad preparation before cleaning and reballing

Compatible Devices

  • Universal scope. The blades work on mobile phone motherboards and screens that need CPU, IC or glue removal, and the tool is not tied to specific models.
  • Mobile phone motherboards, universal and not model-specific
  • CPU and SoC chips after heat softens the glue
  • Screen ICs
  • Small board parts such as separators and chips
  • Screen-side glue areas
  • Android phone boards that need IC-level rework
  • Tablet and gadget boards that need careful prying
  • Boards you prepare for reballing

FAQ

What is the product name?
The product name is 2UUL Hand Finish Blades E Model 4Pcs Set Without Handle.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is the 2UUL DA15 E Model.
What is this product used for?
This product is used for lifting CPUs, screen ICs and small board parts, and for removing glue from the screen during mobile phone repair.
Which devices are compatible with this product?
This product works on mobile phone motherboards and screens as a universal tool and is not limited to specific models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How thin is the blade tip of the 2UUL E model?
The blade tip measures about 0.06mm and the tail measures about 0.3mm, which gives a thin-to-thick profile.
Does the 2UUL E model blade set include a handle?
No. The pack contains four blades without a handle, so you use your own blade holder.