2UUL DA82 Polish Drill Pen Tips 10pcs Replacement Set
₨ 600
2UUL DA82 Replacement Grinding Heads
The 2UUL DA82 polish drill pen tips replace worn heads on your rechargeable grinding pen and keep chip, glue and board work consistent. The 10pcs set packs several head profiles (2.5K, 4.0A, 0.8A and 2.0D, two pieces each), so you can match the head to the job instead of forcing one worn bit through every task. Technicians use these DA82 grinding heads for mobile repair jobs such as OCA glue cleaning, IC drilling, chip grinding and CPU polishing on dead phone boards. The 2.35 mm shank suits the 2UUL DA81 chuck, and the set ships with the DA85 and DA86 grinder kits. Stock a spare set at your bench and keep working without waiting for a new head.
In stock
Keep Your Polish Pen Cutting Clean with 2UUL DA82 Polish Drill Pen Tips
Grinding heads wear faster than the pen that drives them. Epoxy, OCA residue and silicon dust load the cutting surface, and a clogged head drags, overheats and chews the board instead of cleaning it. The 2UUL DA82 polish drill pen tips give your pen ten fresh heads in one pack, so you swap the head and keep the motor, battery and body you already trust. The DA82 designation matches the heads that 2UUL bundles with its DA85 CVT Pro coreless motor grinder and DA86 mini grinder, which makes this set the direct refill for that pen family.
Head Profiles and Chuck Fit
The set contains four head types: 2.5K, 4.0A, 0.8A and 2.0D, with two pieces of each listed profile. Each code marks a different profile and size, so you pick the head by the surface you work on rather than by habit. Test an unfamiliar profile on a scrap board before it touches a live motherboard, and check the contact patch under magnification as you go. The shank measures 2.35 mm, the chuck capacity published for the 2UUL DA81 pen. Seat the shank fully in the collet, tighten it and spin the pen free of the board to confirm the head runs true. A head that wobbles transfers that wobble to the PCB, so reject it. The full pack weighs roughly 50 g, which keeps a spare set easy to carry between benches.
Where These Tips Fit in a Board-Level Repair
You reach for a polish pen at the stage where hot air and a blade stop being precise enough. Typical jobs include clearing hardened OCA glue, grinding the epoxy off a CPU or IC, drilling through a chip when you handle an IC change karna job, and polishing pads and traces after you lift a component. Pair the heads with a microscope so you watch the cut depth, a PCB holder so the board stays still, and a hot air station to soften underfill before you grind. After you finish the cleanup, move to your soldering station and a reballing kit to rebuild the connection. A fresh head matters most on dead phone and hardware fault cases, where one slip across a trace turns a repairable board into scrap.
Choosing and Stocking the Set
Buy this pack when your current heads lose bite, load up with residue or no longer seat cleanly. If you run the 2UUL DA81, the DA85 CVT Pro or the DA86 mini grinder, the DA82 set matches the head type those kits use. Repair shops that grind daily should keep two or three sets on the shelf, because a heavy week of chip and glue work uses up heads quickly. When your volume grows, upgrade the pen itself to the DA85 CVT Pro for its coreless motor and keep the same DA82 heads, so your consumable stock stays standard across benches. Rotate heads by task: dedicate one profile to glue and another to chip work, so residue from rough jobs never touches a fine cleanup.
| Weight | 0.50 kg |
|---|
Key Features
- ✓10pcs replacement set for 2UUL polish drill pens
- ✓Four head profiles in one pack: 2.5K, 4.0A, 0.8A and 2.0D
- ✓2.35 mm shank for the DA81 chuck
- ✓Matches the DA82 heads bundled with the DA85 and DA86 grinders
- ✓Restores cutting performance on worn or clogged pens
- ✓Suits chip grinding, IC drilling and glue cleaning
- ✓Compact pack of roughly 50 g
- ✓Keeps consumable stock standard across 2UUL pen models
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA82 |
| Category | Polish Drill Pen Replacement Tips |
| Compatibility | 2UUL DA81 polish drill pen, DA85 CVT Pro grinder, DA86 mini grinder |
| Pack Quantity | 10pcs per set |
| Head Types Listed | 2.5K x2, 4.0A x2, 0.8A x2, 2.0D x2 |
| Shank Diameter | 2.35 mm |
| Weight | Approx. 50 g |
Common Repair Uses
- ✓Board-level grinding, drilling and cleaning jobs on mobile phone PCBs
- ✓OCA glue cleaning
- ✓Glue and adhesive removal
- ✓IC chip grinding
- ✓CPU polishing
- ✓IC drilling
- ✓Epoxy board processing
- ✓Motherboard and PCB cleanup
- ✓Pad polishing after component removal
Compatible Devices
- ✓Verified scope covers the 2UUL grinding pen family that uses DA82 heads
- ✓2UUL DA81 rechargeable polish drill pen
- ✓2UUL DA85 CVT Pro coreless motor grinder
- ✓2UUL DA86 mini grinder
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What shank size do the DA82 heads use?
Which head types come in the DA82 set?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



