YCS 2020 Desoldering Wick 2.0mm x 2.0m, 5 Pcs Roll

₨ 1,500

YCS 2020 Solder Wick Pack

The YCS 2020 desoldering wick gives your bench a 2.0 mm wide braid with 2.0 m of length on every roll, and this pack contains five rolls. Mechanicpk supplies it for board-level mobile repair, where you pull leftover tin off BGA pads, IC pads and charging port pads after a component comes off. The braid carries good thermal conductivity and strong tin absorption, and it leaves no residue, so your pads stay ready for reballing or direct reseating. One pack covers 10 m of braid in total, which keeps a shared bench stocked through a full week of IC change jobs without a reorder.

In stock

10 People watching this product now!
Description

YCS 2020 Desoldering Wick for Clean Pad Preparation on Mobile Boards

The YCS 2020 desoldering wick gives you a 2.0 mm wide braid with 2.0 m of length on each roll, and the pack ships five rolls. YCS sells this version under its Mr. Yang M.Y line for mobile phone motherboard work. The braid pulls leftover tin off BGA pads, IC pads and charging port pads after you lift a component. If your bench handles IC change karna jobs every day, a five-roll pack keeps you from stopping mid-repair to hunt for fresh braid. The product description highlights good thermal conductivity, strong tin absorption and no residue, which is what you need when you prep pads for reballing or direct reseating.

Why a 2.0 mm Braid Suits Board-Level Work

A 2.0 mm braid covers most pad rows on phone boards without spilling over onto neighbouring passives. You press the braid flat on the pad, set your tip on top, and the molten tin travels into the weave. This width removes bulk tin quickly, yet it still gives you control near the fine-pitch areas around the CPU, eMMC and power ICs. At 2.0 m per roll, you cut short working sections and discard each tinned stretch, so every pass touches clean braid. Pair the wick with a temperature-controlled soldering station or a hot air station, and match your heat to the solder alloy on the board in front of you.

Where It Fits in Your Repair Workflow

Desoldering wick sits between component removal and component fitting. After a hot air station lifts an eMMC, UFS chip, charging IC or audio IC, the pads hold uneven tin that blocks a flat seating. You drag the wick across the pad, collect the excess and leave a smooth surface. Technicians who run ISP pinout work on a dead phone use the same braid to clean test points before they solder fine wires. When a dead after flash fault traces back to a damaged storage chip, you wick the pads, inspect them under a microscope and move on to reballing with a stencil. Keep a multimeter beside you to check for shorts between pads once the surface is clean.

Using the Roll and Stocking the Pack

Place the braid over the joint, press your iron tip onto it and wait for the tin to flow into the weave. Lift the braid and the iron together so you do not tear the pad. Cut off the tinned section after every pass. Hold the braid with tweezers to protect your fingers, and keep heat time short on thin boards. Use light pressure, because gentle contact lifts tin without lifting copper. Store unused rolls dry. The five-roll pack gives you 10 m of braid in total, which suits repair shops where several technicians share one bench and distributors who supply consumables to shop owners across Pakistan. Add PCB holders and a reballing kit to the same order, and you cover the full pad-cleaning and rework sequence from one supplier.

Additional information
Weight0.2 kg
Q & A
Please login to post questions

Key Features

  • 2.0 mm wide braid sized for mobile board pads
  • 2.0 m length on every roll
  • Five rolls in one pack, 10 m of braid in total
  • Good thermal conductivity for quick tin transfer
  • Strong tin absorption for fast pad cleaning
  • Leaves no residue on the cleaned pad
  • Suits BGA, IC and charging port pad work
  • Part of the YCS Mr. Yang M.Y desoldering wick range

Specifications

BrandYCS
Model2020 (Mr. Yang M.Y series)
CategoryDesoldering Wick / Solder Wick
CompatibilityUniversal, not device-specific
DimensionsWidth 2.0 mm, Length 2.0 m per roll
Pack Quantity5 rolls

Common Repair Uses

  • Removing leftover tin from pads during board-level mobile repair
  • Cleaning BGA pads before reballing
  • Cleaning pads after IC change karna jobs
  • Removing excess tin after eMMC or UFS chip removal
  • Cleaning ISP test points on a dead phone
  • Fixing charging port pad bridging from hardware fault repairs
  • Clearing solder bridges between neighbouring pads
  • Preparing pads for direct IC reseating
  • General PCB cleaning and rework

Compatible Devices

  • Universal pad-cleaning scope for mobile phone motherboards, not tied to a single brand or chipset family
  • Mobile phone motherboards across all brands
  • BGA pads on CPU and chipset footprints
  • eMMC and UFS chip pads
  • Charging IC pads
  • Power management IC pads
  • Audio IC pads
  • ISP test point pads
  • Charging port and connector pads

FAQ

What is the product name?
The product name is YCS 2020 Desoldering Wick 5 Pcs Roll.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is YCS 2020 from the Mr. Yang M.Y series.
What is this product used for?
This product removes leftover solder from PCB and BGA pads during mobile phone board repair.
Which devices are compatible with this product?
This product suits mobile phone motherboards in general. It is a universal pad-cleaning consumable, not tied to specific models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What width and length does the YCS 2020 desoldering wick have?
Each roll is 2.0 mm wide and 2.0 m long, and the pack contains five rolls.
Can I use the YCS 2020 desoldering wick to clean BGA pads after an IC change?
Yes. YCS positions this wick for cleaning BGA and PCB pads on mobile phone motherboards, so you can use it to remove leftover tin after you lift an IC.