YCS 2015 Desoldering Wick 2.0mm 1.5m
₨ 300
YCS 2015 Solder Wick for BGA Pad Cleanup
The YCS desoldering wick 2015 is a 2.0mm wide, 1.5 metre braided copper wick built for pulling excess solder off mobile phone motherboards. You use it to clear solder bridges, flatten IC pads before reballing, and clean up after a chip lift on BGA and SMD footprints. The woven copper pulls tin up the braid fast, so your iron spends less time on the pad. This single-roll pack suits technicians who want the YCS 2015 size for everyday board-level work. Add it to your bench next to your hot air station and flux, and you cover pad cleaning on most dead phone and charging issue jobs without a separate desoldering pump.
In stock
YCS Desoldering Wick 2015 for Board-Level Solder Removal
The YCS desoldering wick 2015 is a braided copper solder wick sold under the YCS brand for mobile phone motherboard repair. It measures 2.0mm in width and 1.5m in length, which makes it a practical middle-width wick for IC pads, shield frames, and connector footprints. If you clean pads after every chip change, this roll gives you a consistent, low-residue surface to reball or reflow onto.
How the Copper Braid Pulls Solder
The wick uses a woven pure copper structure. When you press the braid onto molten solder with your iron tip, capillary action draws the tin up into the weave. That means a thin pass clears excess solder without scraping the pad with the iron tip, which protects the pad copper and the solder mask around it. YCS lists good thermal conductivity, strong tin absorption, and no residue as its main claims for this wick, and the tight braid matches that description.
Where It Fits in Your Repair Workflow
After you lift an eMMC, CPU, or power IC with hot air, the pads carry uneven leftover solder. Lay the 2.0mm braid across the pad area, add a little flux, and drag it slowly with your iron. You finish with flat, shiny pads that accept a stencil or a fresh ball cleanly. The same technique removes solder bridges between fine-pitch pins after a rework, and it clears tin from shield cans and connector pads before you swap parts. Technicians handling charging port jobs, display connector faults, and hardware fault diagnosis use the wick for quick tin removal on dense areas where a pump cannot reach.
Choosing the 2.0mm Size
YCS sells this wick family in several sizes, including 2.0mm and 3.5mm widths. The 2015 model sits at 2.0mm by 1.5m, so it covers most phone-board pads without overlapping neighbouring components. Pick a wider roll for large ground planes, and keep this one for IC footprints and connector pads. Cut off the used section with nippers as it fills with tin, and keep a fresh braid end on the pad each time so the wick keeps absorbing.
| Weight | 0.1 kg |
|---|
Key Features
- ✓2.0mm wide braid for IC and connector pads
- ✓1.5m length per roll
- ✓Braided copper construction
- ✓Strong tin absorption through capillary action
- ✓Good thermal conductivity for faster solder pickup
- ✓Low residue finish on cleaned pads
- ✓Suited to BGA reballing preparation
- ✓Single roll pack for individual bench use
Specifications
| Brand | YCS |
|---|---|
| Model | 2015 |
| Category | Desoldering Wick / Solder Braid |
| Material | Braided copper wire |
| Dimensions | Width 2.0mm, Length 1.5m |
Common Repair Uses
- ✓Solder removal at board level on mobile phone PCBs.
- ✓BGA pad cleaning after IC removal
- ✓Solder bridge removal between fine-pitch pins
- ✓Pad flattening before reballing
- ✓eMMC and CPU pad cleanup after lifting
- ✓Shield frame and connector pad cleaning
- ✓Charging port pad rework
- ✓Excess solder removal after a jumper lagana repair
- ✓Pre-reflow cleanup on hardware fault boards
Compatible Devices
- ✓Universal — not device-specific. The wick works on any PCB solder joint, so it applies to motherboards from the following brands and board types.
- ✓Samsung boards
- ✓Oppo boards
- ✓Vivo boards
- ✓Infinix boards
- ✓Tecno boards
- ✓Xiaomi and Redmi boards
- ✓iPhone logic boards
- ✓BGA and SMD IC pads on any mobile phone PCB
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the width and length of the YCS 2015 desoldering wick?
Is the 2.0mm wick suitable for cleaning BGA pads before reballing?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



