Mijing 150°C Solder Paste for BGA & SMD Mobile Repair

₨ 800

Low-Temp Mijing Solder Paste

Mijing 150°C solder paste comes in a needle tube that lets you place measured beads on BGA pads, stencil openings and SMD footprints. The 150°C melting point suits mobile phone motherboard rework where you want less heat on the board and on nearby components. You use it for CPU, eMMC, power IC and audio IC reballing, for refitting small SMD parts, and for re-tinning lifted pads after an IC change. Pair it with a hot air station and a microscope for clean, repeatable joints. Mechanicpk supplies Mijing solder paste to repair shops and technicians across Pakistan.

In stock

11 People watching this product now!
Description

Mijing 150°C Solder Paste for Mobile Board Rework

Mijing 150°C solder paste gives your bench a low-melt option for reballing and SMD work on mobile phone motherboards. The needle tube keeps the paste sealed and lets you place it exactly where the pad needs it, which matters on dense BGA footprints under a microscope. Mijing offers its needle tube tin paste across a range of melting points from 138°C to 217°C, and the 150°C variant sits at the low-temperature end of that range. This listing targets technicians who already know their rework process and want a dependable paste to match it.

Where 150°C Fits in the Repair Workflow

A lower melting point means your hot air station does less work to reflow each joint. That helps when a board has already taken heat during IC removal, and when neighbouring components sit close to the chip you rework. On a dead phone with a hardware fault, you lift the failed IC, clean the pads, spread paste through a stencil, and reflow it into balls before you place the chip back. The same paste handles IC change karna jobs where you refit a power IC, audio IC or charging IC on pads that need fresh solder. Boot loop issue and hang on logo faults often trace back to a weak eMMC or CPU ball, and reballing with a fresh paste layer addresses that cause directly.

Applying Paste from the Needle Tube

Push the plunger slowly and lay a small bead instead of a large dollop. A thin, even layer through a BGA stencil gives you uniform balls, while excess paste bridges neighbouring pads. Spread the paste with a flat blade at a sharp angle so it packs into every stencil opening, then lift the stencil straight up. Wipe the tip and cap the tube tightly after each job so the flux does not dry inside the nozzle. Store the tube in a cool place away from direct sun. If the paste turns dry or chunky, replace it, because aged paste produces grey joints and weak balls.

Why Technicians Choose a 150°C Paste

Heat control decides the outcome on tightly packed boards. A 150°C paste lets you reflow at a gentler setting than the 183°C, 199°C and 217°C variants in the same Mijing range, so you keep stress off plastic connectors, shields and adjacent ICs. Choose a higher-melt variant when the job demands a stronger joint or when you work on boards that run hot in service. Many workshops keep several melting points on the bench and match each paste to the board in front of them. Build your setup around a hot air station, a reballing kit, a set of stencils, a PCB holder and a microscope from the Mechanicpk range, and you cover the full reballing sequence from IC removal to final reflow.

Additional information
Weight0.50 kg
Q & A
Please login to post questions

Key Features

  • 150°C melting-point variant for low-heat rework
  • Needle tube packing for controlled bead placement
  • Suits stencil-based BGA reballing
  • Works on SMD footprints and bare pads
  • Fits mobile phone motherboard repair workflows
  • Part of a Mijing range covering 138°C to 217°C
  • Pairs with hot air stations and microscopes
  • Suits daily workshop use in repair shops and service centers

Specifications

BrandMijing
CategorySoldering Supplies / Reballing Solder Paste
CompatibilityMobile phone motherboards, BGA and SMD components
Supported DevicesUniversal — not device-specific
TechnologyLow-temperature solder paste, 150°C melting-point variant, needle tube packing

Common Repair Uses

  • Reballing, pad re-tinning and SMD rework on mobile phone motherboards
  • BGA CPU reballing through a stencil
  • eMMC and NAND reballing
  • Power IC and charging IC refit after IC change
  • Audio IC reattachment
  • Re-tinning lifted or bare pads
  • SMD resistor, capacitor and connector rework
  • Repair of dead phone boards after IC removal
  • Boot loop and hang on logo repairs that need a reballed chip

Compatible Devices

  • Universal solder paste for mobile phone and electronic circuit board rework — not limited to specific models
  • Android smartphone motherboards
  • iPhone logic boards
  • BGA CPU and SoC packages on phone boards
  • eMMC and NAND memory chips
  • Power management ICs
  • Audio and charging ICs
  • SMD components on mobile PCBs
  • Laptop and general electronic circuit boards

FAQ

What is the product name?
The product name is Mijing 150°C Solder Paste Liquid Soldering Welding Paste.
What is the brand of this product?
The brand of this product is Mijing.
What is this product used for?
This product is used for BGA reballing, SMD soldering and pad re-tinning on mobile phone motherboards and electronic circuit boards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is Mijing 150°C solder paste suitable for BGA reballing on mobile CPUs?
Yes. Mijing sells its needle tube tin paste for BGA chip soldering and repair on mobile phone motherboards, and the 150°C variant works with a stencil and hot air station for reballing.
What temperature should I set on my hot air station for this paste?
The paste melts at 150°C, so set your hot air station above that point and raise the heat gradually until the balls form. The exact setting depends on your station, nozzle and board.
Which other melting points does Mijing offer in this paste range?
Mijing lists its needle tube tin paste at 138°C, 150°C, 183°C, 199°C and 217°C, so you can match the melting point to the board and the job.
Which devices are compatible with this product?
This paste is universal. It suits mobile phone motherboards, BGA ICs and SMD components rather than specific phone models.