YCS Universal Magnetic Glue Removal Platform
₨ 2,400
Magnetic Glue Removal Platform for CPU Rework
The YCS magnetic glue removal platform holds your reballing stencil and chip steady during the glue removal and tin planting stages of mobile board repair. A magnetic design, clamping action and high-temperature synthetic stone body give you a stable base for iPhone and Android CPU rework. Anti-slip rubber foot pads keep the fixture planted on your bench while you work under a microscope. Mechanicpk supplies it for technicians and repair shops across Pakistan who run regular IC change and reballing jobs. You pair it with the matching YCS stencil set for your chip family. Stencils sell separately.
In stock
Magnetic Glue Removal Platform for Mobile Board Rework
The YCS magnetic glue removal platform gives your repair bench a flat, fixed surface for the messiest step of CPU and IC rework: clearing epoxy and underfill from a lifted chip and its pads. A magnetic design holds the reballing stencil and chip position steady, so your blade, hot air nozzle and solder paste work on a target that stays where you put it. Mechanicpk supplies this fixture to workshops that handle iPhone and Android boards every day and want repeatable results on dead phone cases and hardware fault jobs.
Where the Platform Fits in Your Rework Sequence
A CPU or eMMC job follows a fixed order. You lift the chip with a hot air station, strip the glue, clean and detin the pads under a microscope, plant fresh tin through a stencil, then reflow. This platform covers the middle of that chain, from glue removal through tin planting. Instead of juggling a loose stencil, tweezers and a board that slides on the mat, you work on one stable base. That matters most on IC change karna jobs, where a single shifted stencil means you start the planting step again. Because glue removal and tin planting share one base, you also cut the number of fixtures on a crowded bench, which helps small shops that run several jobs at once.
Why the YCS Magnetic Glue Removal Platform Suits Stencil Work
The magnetic design keeps the stencil flat against the chip while you spread solder paste, and the clamping action holds the chip firmly without crushing it. YCS builds the body from high-temperature and corrosion-resistant synthetic stone, a surface that resists staining from flux and residue and wipes clean between jobs. Anti-slip rubber foot pads grip the bench, which helps when you scrape glue under a microscope and every small vibration shows up on screen. Heavy glue still needs patience: soften it with heat, remove it in thin layers and stop as soon as bare pad shows.
The platform handles the holding. The chip family decides which stencil you need. YCS lists separate stencil sets for iPhone A-series CPUs, Qualcomm, HiSilicon, MediaTek Dimensity, Samsung and Kirin processors, and those sets sell apart from the platform. Check the stencil set that matches your daily board mix before you order, because a shop that repairs mostly Infinix and Tecno boards needs a different set from a shop that focuses on iPhone logic boards.
How to Build the Rest of Your Bench Around It
Glue removal works best when your heat source and your magnification are right. Pair the platform with a Hot Air Station that holds a stable temperature at low airflow, a Soldering Station for pad cleaning, and a Microscope that lets you see the edge of the pad while you cut residue. Keep a Reballing Kit and fresh flux nearby, a PCB Holder for the rest of the board, and a Multimeter to check continuity before you close the phone. If your workflow also includes dead-after-flash eMMC cases, ISP Pinout Tools and eMMC Programmers sit upstream of this step, because you confirm the fault first and move to chip-level rework only when the data lines point to a bad chip.
Technicians who start with a basic PCB holder often move to a magnetic platform once their reballing volume grows. The jump removes the most common source of rework on the bench: a stencil that shifts mid-reflow. Your hang on logo and boot loop issue repairs finish faster when the planting step goes right on the first pass.
Handling Notes Before You Start
Apply heat in short, controlled passes and let the platform cool before you clean it. YCS does not publish a maximum temperature rating for this body, so treat your station’s own safe working range as the limit instead of pushing the platform. Wipe the stencil seat before each board so leftover tin does not lift the stencil and break the contact the magnet creates. Clean residue with isopropyl alcohol after every job, and the synthetic stone surface stays flat and ready for the next board.
| Weight | 0.18 kg |
|---|
Key Features
- ✓Magnetic design that holds the stencil firmly in position
- ✓Clamping action that grips the chip without excess pressure
- ✓High-temperature-resistant synthetic stone body
- ✓Corrosion-resistant, anti-fouling surface that wipes clean
- ✓Anti-slip rubber foot pads for bench stability
- ✓Multi-purpose use: glue removal, detinning and tin planting
- ✓Works with YCS stencil sets for iPhone, Qualcomm, HiSilicon, MediaTek, Samsung and Kirin CPUs
- ✓Universal platform approach across iPhone and Android boards
Specifications
| Brand | YCS |
|---|---|
| Category | PCB Stand & Fixture / Glue Removal and Reballing Platform |
| Compatibility | Magnetic reballing stencils (stencil sets sold separately) |
| Supported Devices | iPhone and Android CPU families through the matching YCS stencil set |
| Technology | Magnetic stencil positioning with clamping action |
| Material | High-temperature and corrosion-resistant synthetic stone body with anti-slip rubber foot pads |
Common Repair Uses
- ✓Glue removal, detinning and tin planting during chip-level board rework
- ✓Epoxy glue removal around CPU and IC areas
- ✓Pad detinning before fresh tin planting
- ✓Tin planting through a magnetic stencil
- ✓CPU reballing after IC change karna
- ✓Holding the board steady while you clean pads under a microscope
- ✓Stencil-fixed solder paste application before reflow
Compatible Devices
- ✓Chip-family scope, set by the stencil you pair with the platform
- ✓Apple iPhone A-series CPUs (YCS A8–A19 Pro stencil set)
- ✓Qualcomm CPUs (YCS Qualcomm stencil sets)
- ✓HiSilicon CPUs (YCS HiSilicon stencil sets)
- ✓MediaTek Dimensity CPUs (YCS MediaTek stencil sets)
- ✓Samsung CPUs (YCS Samsung stencil sets)
- ✓Kirin CPUs (YCS Kirin stencil set)
FAQ
What is the product name?
What is the brand of this product?
What is the platform made from?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which stencil do I need for the YCS magnetic glue removal platform?
Can I use hot air on this platform during glue removal?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



